Electrocardiogram (ECG) is an essential route to monitor and prevent cardiovascular related disease. Conventional silver/silver chloride (Ag/AgCl) electrodes are not able to be used for long-term monitoring due to the drying of gel and skin irritation. Graphene has been investigated as a promising material for wearable health-monitoring electronics. Here, a graphene-coated textile electrode was developed for ECG monitoring. The graphene electrode was prepared by screen printing graphene ink on a pre-modified textile substrate. The electrical resistance of the graphene textile electrode can be controlled by increasing the printing passes. The ECG signals obtained by the graphene textile electrode showed comparable performance to the conventional Ag/AgCl electrode. The graphene textile electrode shows satisfactory washability, high flexibility and good tortuosity. The performance of the ECG signal shows negligible change over nine washing cycles and 2000 bending cycles. Overall, the screen-printed graphene textile electrode in this work presents an inexpensive fabrication platform solution for long-term healthcare monitoring in wearable electronics.
23 August 2019 in Journal of Physics D: Applied Physics
Silver nanowires (AgNWs) have attracted considerable attention as the material for emerging flexible, high conductive, and transparent wearable healthcare monitoring. However, due to the high possibility of AgNWs being oxidized in air and the discomfort caused by direct contact between silver nanowires and human skin, there are still some concerns to be taken into account in the direct application of AgNWs to ECG electrodes. Here, we combined AgNWs with graphene oxide (GO), and adopted the screen-printing technology for the fabrication of AgNWs/GO hybrid transparent conductive electrodes. Using the screen-printing technology throughout the whole fabrication process gives the ability to fabricate patterned films easily, and has the advantages of simple control and low cost, which makes it superior in mass production compared to previous studies. By encapsulating the AgNW with the GO layer, the electrodes obtained exhibit excellent optical and electrical properties (transmittance of 83.5% at 550 nm and sheet resistance of 11.9 Ohm/sq). Apart from optical and electrical properties, with GO as a protective layer, the reliability, bio-friendliness and long-term stability of AgNWs/GO hybrid electrodes have been greatly improved. In addition, AgNWs/GO electrodes fabricated on PET substrate also show excellent mechanical flexibility. We anticipate that AgNWs/GO electrodes will be promising materials for the implementation of emerging portable healthcare electronics such as wearable ECG monitoring.
The aim of this study was to explore the feasibility of using different 3D printed internal geometries as tablet formulations to obtain controlled release profiles. In order to obtain controllable release profiles, three types of tablet models (Cylinder, Horn and Reversed Horn) with controlled structures were designed. The cylinder model shows a constant release profile and can keep the drug concentration within a certain range. The horn model exhibits an increasing release profile, which is suitable for the patients who have the drug resistance in the course of medication. The reversed horn model has a decreasing release profile that would be applied to hypertension cure. Furthermore, three types of tablets were fabricated successfully by a fused deposition modeling three-dimensional (3D) printer and injected with paracetamol (APAP) -containing gels. The results of in vitro drug release demonstrate that tablets with three kinds of structures can produce constant, gradually increasing, and gradually decreasing release profiles, respectively. The release attributes can be controlled by using different 3D printed geometries as tablet formulations. More importantly, there are no residues after dissolution. The method of preparing customized tablets with distinguished release profiles presented in this study has the promising potential in the fabrication of patient-tailored medicines.
Electrocardiogram (ECG) signals are crucial for determining the health status of the human heart. A clean ECG signal is critical in analysis and diagnosis of heart diseases. However, ECG signals are often contaminated by motion artifact noise in the non-contact ECG monitoring systems. In this paper, an ECG motion artifact removal approach based on empirical wavelet transform (EWT) and wavelet thresholding (WT) is proposed. This method consists of five steps, namely, spectrum preprocessing, spectrum segmentation, EWT decomposition, wavelet threshold denoising, and EWT reconstruction. The proposed approach was used to process real ECG signals collected by the non-contact ECG monitoring equipment. The results of quantitative study and analysis indicate that this approach produces a better performance in terms of restorage of QRS complexes of the original ECG with reduced distortion, retaining useful information in ECG signals, and improvement of the signal to noise ratio (SNR) value of the signal. The output results of the practical ECG signal test show that motion artifact in the real recorded ECG is effectively filtered out. The proposed method is feasible for reducing motion artifacts from ECG signals, whether from simulation ECG signals or practical non-contact ECG monitoring systems.
The fluctuation of the stretched resistance of composites based on inkjet-printed silver nanowires (AgNW) and polydimethylsiloxane (PDMS) is controlled by different ratios of a curing agent in PDMS, with an optimized normalized resistance change as low as 4.67% in a 50% tensile testing cycle. The results confirm that the properties of PDMS including the Young’s modulus and creep deformation play key roles in controlling the resistance changes of stretched AgNW–PDMS composites based on inkjet-printed AgNW, which opens up applications of inkjet-printable elastic AgNW conductors in stretchable electronics.