This paper presents a review on the recent research and technical progress of electric motor systems and electric powertrains for new energy vehicles. Through the analysis and comparison of direct current motor, induction motor, and synchronous motor, it is found that permanent magnet synchronous motor has better overall performance; by comparison with converters with Si-based IGBTs, it is found converters with SiC MOSFETs show significantly higher efficiency and increase driving mileage per charge. In addition, the pros and cons of different control strategies and algorithms are demonstrated. Next, by comparing series, parallel, and power split hybrid powertrains, the series–parallel compound hybrid powertrains are found to provide better fuel economy. Different electric powertrains, hybrid powertrains, and range-extended electric systems are also detailed, and their advantages and disadvantages are described. Finally, the technology roadmap over the next 15 years is proposed regarding traction motor, power electronic converter and electric powertrain as well as the key materials and components at each time frame.

In world practice, the role of reproduction of raw material base of oil production by implementing modern methods of oil recovery enhancement (thermal, gas, chemical, microbiological) on the basis of innovative techniques and technologies is rapidly growing and is becoming more important. It is concluded that at present, the priority of increasing oil reserves in world oil production is the development and industrial introduction of modern integrated methods of enhanced oil recovery, which can provide a synergistic effect in the development of new and developed oil fields. This article presents a review and comparative analysis of theoretical and practical methods of improving oil recovery of conventional and unconventional reservoirs. The paper examines in detail methods of improving oil recovery, taking into account the factors of enhanced oil recovery of oil reservoirs. Considered the main methods and technologies currently used to develop oil fields and recommendations for their effective use, taking into account the variety of external factors of oil production: the geological structure of the reservoir, its volume, and properties of oils. It is shown that there is no universal method of oil reservoir development, and it must be chosen after a thorough feasibility study among several proposed models. When describing the methods of enhanced oil recovery, special attention is also paid to the physical processes that occur as a result of applying the technology. In conclusion, the positive and negative characteristics of the presented methods included in EOR are presented, and recommendations that may influence the choice of practical solutions for engineers and oil producers are given. Conclusions are made that development systems, placement and choice of operating mode of wells essentially depend on the geological structure of the reservoir, its volume and properties of oils. An important role in this is the construction of a geological model of the production facility. The used hydrodynamic models of development are based on physical laws, about which oil producers sometimes don’t even suspect, and the authors of the models are not always able to convey it to the real producers. The authors consider it reasonable to make a logical generalizing conclusion that understanding processes occurring in the reservoir and taking appropriate measures for optimization and intensification of oil production will allow making oil production as effective as possible.

The DC-DC converter for fuel cell vehicles should be characterized by high-gain, low voltage stress, small size and high-efficiency. However, conventional two-level, three-level and cascaded boost converters cannot meet the requirements. A new non-isolated DC-DC converter with switched-capacitor and switched-inductor is proposed in this paper, which can obtain high-gain, wide input voltage range, low voltage stresses across components and common ground structure. In this paper, the operating principle, component parameters design, and comparisons with other high-gain converters are analyzed. Moreover, the state-space averaging method and small-signal modeling method are adopted to obtain the dynamic model of converter. Finally, simulation and experimental results verify the effectiveness of the proposed topology. The input voltage of the experimental prototype ranges from 25V to 80V. The rated output voltage is 200V and rated power is 100W. The maximum efficiency is 93.1% under rated state. The proposed converter is suitable for fuel cell vehicles.

Online State of Charge (SoC) and State of Health (SoH) estimation is essential for efficient, safe, and reliable operation of Lithium ion batteries. Based on the first-order equivalent circuit model (ECM), a multi-scale extended Kalman filter is adopted in this paper to estimate ECM parameters and battery SoC using dual time scales. The nature of the battery excitations significantly influences the estimation performance. When the input-output data, i.e., the input current and output voltage, is insufficiently rich in frequency content, the estimation performance is poor. Thus the excitation current should be optimized for accurate estimation of parameters and states. A Cramer-Rao bound analysis is conducted, considering voltage noise, current amplitude, and current frequency, which shows the loss of accuracy in multi-parameter estimation (estimating all states and parameters) when compared to single-parameter estimation (estimating only one parameter/state). However, it also shows that the loss of accuracy can be significantly reduced when the excitation current is carefully chosen to satisfy certain criteria. Both simulation and experimental results verify the analysis results and show that a current profile with optimal frequency components achieves the best estimation performance, thereby providing guidelines for designing battery current profiles for improved SoC and SoH estimation performance.