Two new binary liquid crystalline mixtures composed from the chiral liquid crystalline materials with partially fluorinated non-chiral chain and without lateral substitution at the molecular core have been designed and investigated by polarisation optical microscopy, differential scanning calorimetry, broad-band dielectric spectroscopy, and X-ray techniques. Both mixtures possess the paraelectric orthogonal smectic A*, the tilted ferroelectric smectic C* and the antiferroelectric smectic CA* phases over a reasonably broad temperature range. The gained results reveal a considerable improvement of (i) the broadness of the mesophases temperature range of the ferroelectric and antiferroelectric phases (up to 130 K breadth) and (ii) electro-optical properties, namely the spontaneous polarisation (up to 200 nC/cm2) and tilt angle (higher than 40o), with respect to that of the original pure compounds.
The article presents the basic conceptual assumptions of a photobioreactor with a complementary lighting system. The cylindrical bioreactor has three independent, interconnected, and fully controlled lighting systems. A characteristic feature is the combination of the lighting system with the measurement of photosynthetically active PAR (photosynthetically active radiation) and the optical density of the culture medium. The entire lighting system is based on RGBW (“red, green, blue, white”) LED and RBG (“red, green, blue”) LEDs. The pilot study was conducted on a simplified prototype of a photobioreactor designed for the distribution and optimization of light in algae cultures designed for energy purposes. The study was carried out on microalgae Chlorella Vulgaris BA0002a from the collection of marine algae cultures.
The motion of a solid particle introduced into a stream of fluid is a crucial problem in the contexts of pneumatic transport and the purification and separation of non-uniform mixtures. However, the complexity of the underlying equations of motion enforces the creation of semi-empirical models. Therefore, analysis of particle motion in a pneumatic channel was performed. To reduce the number of independent variables, several simplifying assumptions were made in regard to both the particle and the stream. The resulting model provides trajectory equations for a particle introduced into the stream at given values of the initial angle and initial velocity, which are then solved using numerical integration methods. A hodograph function was formulated on the basis of the Runge–Kutta and NDFs methods to test the correctness of the solutions under various initial parameters and to provide a universal method of solving the equations of motion. To verify the model, terminal velocities were measured and particle trajectories recorded using an original experimental stand. The predictions of the model were subsequently compared to these empirical trajectories and were found to fall within the range of uncertainty.
Increasing production of municipal solid waste (MSW) drives the need for its disposal in a manner that is safe for the environment and human health. However, this may require short- or long-term storage before it can be properly processed. Similarly, a way of processing waste material is necessary for the re-cultivation of dump sites. This article presents the results of an investigation into the effects of long-term open-air storage upon waste material to be turned into refuse-derived fuel (RDF) by standard methods for the assessment of MSW and RDF pellet quality including bomb calorimetry, sieve analysis, furnace drying/burning for water/ash content assessment, and pellet expansion measurements. Results of the investigation indicate that such a form of storage bears no notable negative effect on the quality of the material; the pellet expansion coefficient, heat of combustion, and ash content were all found to be approximate to pre-storage values, with positive implications for the storage of solid waste and the prospects of its subsequent processing into solid fuel. It is shown that such material can be stored in open-air conditions for prolonged periods without the loss of desired parameters. In addition, a discussion of differences between the properties of material drawn from varying depths of the pile is provided and the potential impact of the findings in the context of the production and the storage of refuse-derived fuel is assessed.
Lead-free K0.5Bi0.5TiO3 (KBT) ceramics were prepared using a finely tuned convectional solid-state reaction method. Their phase transitions in unpoled and poled states were examined. The temperature-dependent evolution of the reflections sensitive to structural changes and their 2Θ-positions indicated two temperature-driven phase transitions: tetragonal–tetragonal at about 200 °C, and tetragonal–cubic at around 400 °C. These structural transformations are further corroborated by studies examining Raman spectroscopy, dielectric properties, and mechanical properties. It was demonstrated that a prior E-field poling process significantly influences the polar state, causing an increase in the local degree of order, as well as the transformation of the cubic phase into the tetragonal one. This stabilizes and widens the temperature range of the ferroelectric phase. It was found that phase transformations in KBT are accompanied by a softening of the mechanical behavior similarly to improper ferroelastic transformations. The results demonstrate that KBT possesses favorable structural, dielectric, and mechanical characteristics, making it a potential candidate for electronic applications. The present study provides a clear understanding of the multi-scale structural behavior in multi-phase KBT, bridging micro-heterogeneity behaviors and macro-properties, and demonstrates an effective method of tuning the properties of KBTs by E-poling with a low electric field.