A coupled heat source model that combined a Gauss surface heat source with a Gauss cylindrical volumetric heat source was introduced to simulate temperature field distribution and melt pool characteristics using a finite element simulation (FEM) method for the deep and narrow melt pools formed in laser powder bed fusion (L-PBF) aiming at commercial pure titanium (CP-Ti). For comparison, the same simulations using the Gauss surface heat source model and the double ellipsoid heat source model were also performed. The simulated melt pool geometries using the coupled heat source model match well with the measurements, with an average error of 1% for the melt pool depth and 7% for the width. Based on the single-track experimental results, it was found by comparing the simulated results from the three heat source models that the coupled heat source model had better accuracy than the other two. Then, the temperature field and the melt pool geometries of CP-Ti fabricated at different laser power levels from 300 W to 500 W and scanning speeds from 600 mm/s to 4000 mm/s were simulated. According to the simulated maximum temperature and geometries of the melt pool, a suitable process parameters map for CP-Ti was obtained. The reported experimental results agree well with the simulated map. The coupled heat source model is more accurate and applicable for the deep and narrow melt pools formed during L-PBF.

Low-alloy steel samples were successfully fabricated by selective laser melting (SLM). The evolution of the microstructure and the mechanical properties were investigated with different values of the energy area density (EAD). The results revealed that the initial solidification microstructures of the single tracks with different EADs were all martensite. However, the microstructures of bulk samples under different EADs were not martensite and differed significantly even from one another. When EAD increased from 47 to 142 J/mm², the mixed lower bainite and martensite austenite microstructure changed to granular bainite; further, the morphology of bainite ferrite gradually changed from lath to multilateral. Moreover, with the increase of EAD, the grain size was remarkably reduced because of the increasing austenitizing periods and temperature during thermal cycling. The average grain size was 1.56 µm, 3.98 µm, and 6.31 µm with EADs of 142 J/mm², 71 J/mm², and 47 J/mm², respectively. Yield strength and tensile strength of the SLM low-alloy steel increased with the increase in EAD; these values were significantly more than those of the alloys prepared by traditional methods. The microstructure of the SLM low-alloy steel samples is not uniform, and the inhomogeneity becomes more significant as EAD decreases. Simultaneously, when EAD decreases, the fracture mechanism changes from ductile to a mixture of ductile and brittle fracture; this is in contrast to the samples prepared by traditional methods. This study also found a stress concentration mechanism around large pores during plastic deformation that resulted in a brittle fracture. This indicates that large-sized pores significantly degrade the mechanical properties of the specimens.

Aiming at the high-value application of rare earth elements lanthanum (La), an Al-50% La alloy was selected and prepared in a vacuum medium-frequency induction furnace. The geometric characteristics of the Al-50% La alloy powders were compared and studied, with the powders prepared by two different methods: mechanical pulverization and gas atomization. The results showed that an Al-49.09% La master alloy was obtained, and the only intermediate phase containing La in the experimental alloy was Al₁₁La₃. From the perspectives of chemical and phase composition, La has a high yield. Additionally, an Al-La alloy with controllable rare earth intermediate phases can be obtained. The Al-La alloy powders prepared by the mechanical pulverization method are irregular in shape, but the particle size is relatively small, ranging from 0.25 to 66.9 μm. Submicron powders were obtained, with 4.38% of the powders having an equivalent particle size of less than 1 μm. Considering the characteristic of the selective laser melting (SLM) process forming micro-melt pools, a small amount of submicron Al-La alloy powders prepared by the mechanical pulverization method can be used as a trace additive for SLM preparation of CP-Ti. The powders prepared by gas atomization have good sphericity, with a particle size range of 1.65 to 76.0 μm. Among them, the powders with a size of 2–10 μm account for 75.52%, and this part of the powders can be used for the powder metallurgy preparation of composite materials.