Shiyun Dong

Shiyun Dong

Auto-generated profile, based on publicly available information

Shiyun Dong

National Key Laboratory for Remanufacturing, Army Academy of Armored Forces, Beijing 100072, China

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
ZCZhaoxing Cui
Zhaoxing Cui
XHXiaodong Hu
Xiaodong Hu
SDShiyun Dong
Shiyun Dong
SYShixing Yan
Shixing Yan
XZXuan Zhao
Xuan Zhao
The performance and service life of the nuclear emergency diesel engine shaft made of 12CrNi2 alloy steel is very important for the safety of nuclear power. Laser melting deposition (LMD) is a challenging camshaft-forming technology due to its high precision, rapid prototyping, and excellent parts performance. However, LMD is an unsteady process under the local action of laser, especially for curved surface forming, which is more likely to generate large residual stress on components, resulting in cracks and other defects. At present, the stress research on LMD curved surface forming is relatively insufficient. In the present paper, material parameter testing, high-temperature mechanical properties analysis, single-track sample preparation, and heat source checks are conducted. At the same time, the ABAQUS software and the DFLUX heat source subroutine are used to compile the curved double-ellipsoidal moving heat source, and the effects of the temperature-dependent thermophysical parameters and phase change latent heat on the temperature field are considered. A three-dimensional finite element model is established to analyze the thermal stress evolution and residual stress distribution of multi-track multi-layer on a curved surface by LMD, and the effect of the scanning method and interlayer cooling time on the residual stress of the formed components is studied. The results show that with the increase in temperature, the strength of the material reduces, and the fracture morphology of the material gradually transitions from ductile fracture to creep fracture. The material parameters provide a guarantee for the simulation, and the errors of the width and depth of the melt pool are 4% and 9.6%, respectively. The simulation and experiment fit well. After cooling, the maximum equivalent stress is 686 MPa, which appears at the junction of the substrate and the deposited layer. The larger residual stress is mainly concentrated in the lower part of the deposited layer, where the maximum circumferential stress and axial stress are the tensile stress. Compared with the axial parallel lap scanning method, the arc copying lap scanning method has a relatively smaller maximum thermal stress and residual stress after cooling. The residual stress in the deposited layer is increased to some extent with the increase in the interlayer cooling time.

1 October 2005 in Journal of Central South University of Technology
Verified
Journal Article
Closed access
PDF file
SDShi-Yun Dong
Shi-Yun Dong
BXBin-Shi Xu
Bin-Shi Xu
LDLing-Zhong Du
Ling-Zhong Du
HYHua Yang
Hua Yang

4 November 2019 in Materials
Verified
Journal Article
Open access
PDF file
XKXueliang Kang
Xueliang Kang
SDShiyun Dong
Shiyun Dong
HWHongbin Wang
Hongbin Wang
SYShixing Yan
Shixing Yan
XLXiaoting Liu
Xiaoting Liu
HRHuiping Ren
Huiping Ren
Low-alloy steel samples were successfully fabricated by selective laser melting (SLM). The evolution of the microstructure and the mechanical properties were investigated with different values of the energy area density (EAD). The results revealed that the initial solidification microstructures of the single tracks with different EADs were all martensite. However, the microstructures of bulk samples under different EADs were not martensite and differed significantly even from one another. When EAD increased from 47 to 142 J/mm2, the mixed lower bainite and martensite austenite microstructure changed to granular bainite; further, the morphology of bainite ferrite gradually changed from lath to multilateral. Moreover, with the increase of EAD, the grain size was remarkably reduced because of the increasing austenitizing periods and temperature during thermal cycling. The average grain size was 1.56 µm, 3.98 µm, and 6.31 µm with EADs of 142 J/mm2, 71 J/mm2, and 47 J/mm2, respectively. Yield strength and tensile strength of the SLM low-alloy steel increased with the increase in EAD; these values were significantly more than those of the alloys prepared by traditional methods. The microstructure of the SLM low-alloy steel samples is not uniform, and the inhomogeneity becomes more significant as EAD decreases. Simultaneously, when EAD decreases, the fracture mechanism changes from ductile to a mixture of ductile and brittle fracture; this is in contrast to the samples prepared by traditional methods. This study also found a stress concentration mechanism around large pores during plastic deformation that resulted in a brittle fracture. This indicates that large-sized pores significantly degrade the mechanical properties of the specimens.

1 September 2021 in China Foundry
Verified
Journal Article
Closed access
PDF file
SDShi-Yun Dong
Shi-Yun Dong
XZXuan Zhao
Xuan Zhao
SYShi-Xing Yan
Shi-Xing Yan
YLYao-Hui Lü
Yao-Hui Lü
XLXiao-Ting Liu
Xiao-Ting Liu
BXBin-Shi Xu
Bin-Shi Xu

4 June 2025 in Royal Society Open Science
Verified
Journal Article
Open access
LWLixin Wang
Lixin Wang
XJXinyu Jiang
Xinyu Jiang
GYGuang Yang
Guang Yang
SDShiyun Dong
Shiyun Dong
SYShixing Yan
Shixing Yan
The damage to brake discs in heavy-duty vehicles caused by uneven wear is usually repaired with milling method, which reduces their radius and accordingly shortens their service life. Laser cladding repair can maintain the radius, thereby gradually becoming a promising method for brake disc repair, but the complexity of the laser cladding process causes the cladding layer to generate defects that decrease the repair quality. Here, we studied the regulation mechanism of laser power, beam diameter and scanning speed in the cladding layer’s quality via simulation and experiment. Simulation results showed that with the increase of laser power and the decrease of beam diameter or scanning speed, the molten pool’s temperature and flow rate, and the cladding layer’s residual stress have varying degrees of increase. We then fabricated laser cladding samples (Ni60/WC on ductile iron) and acquired their micromorphology, dilution rate and microhardness, and analyzed their regulation mechanism. Experiment results exhibited that the cladding process with laser power 1400 W, beam diameter 3 mm and scanning speed 10 mm/s can make the cladding layer have a better quality. This study provides an available reference for the laser cladding repair of uneven wear in brake discs from heavy-duty vehicles.

13 February 2019
Verified
Book Chapter
Open access
PDF file
SDShi-Yun Dong
Shi-Yun Dong
XFXiang-Yi Feng
Xiang-Yi Feng
JFJin-Xiang Fang
Jin-Xiang Fang
SYShi-Xing Yan
Shi-Xing Yan
It briefly introduced laser remanufacturing, which was an advanced repairing method to refabricate damaged components based on laser forming technologies. The possible factors in determining the performance of the laser remanufacturing FV520B were studied by numerical simulation and experimental methods. First, the results of free dilatometry test showed that the volume effect of phase transformations were corresponding to the transformation temperatures and heating rate of the laser process had remarkable effects on the kinetics of phase transformation. In addition, the evolution of temperature fields of the single-pass and multi-layer laser cladding processes were analyzed by numerical simulation method based on deactivate and reactivate element theory. A combined method of dilatometry and metallography was conducted to reveal the effect of cooling condition and phase transformation on the microstructure of HAZ. The maximum temperature of thermal cycle had a dominating effect on the microstructure, microhardness and phase transformation temperature rather than cooling rate. Thermal cycles had a significant effect on the metallographic transformation and consequently decided the mechanical performance. Microhardness and tensile tests were conducted and the results showed that strength and ductility of laser remanufacturing FV520B were equivalent to that of forgings.