A successful utilization of deep geothermal resources requires accurate predictions about the distribution of reservoir temperature as well as of the hydraulic processes exerting a direct influence on the productivity of geothermal reservoirs. The aim of this study was to investigate and quantify the influence that regional thermo-hydraulic processes have on the geothermal configuration of potential reservoirs in the German Federal State of Hesse. Specifically, we have addressed the question of how the regional thermal and hydraulic configuration influence the local hydro-thermal reservoir conditions. Therefore, a 3D structural model of Hesse was used as a basis for purely hydraulic, purely thermal and coupled 3D thermo-hydraulic simulations of the deep fluid flow and heat transport. As a result of our numerical simulations, Hesse can be differentiated into sub-areas differing in terms of the dominating heat transport process. In a final attempt to quantify the robustness and reliability of the modelling results, the modelling outcomes were analyzed by comparing them to available subsurface temperature, hydraulic and hydrochemical data.
In this study we make use of 3-D hydraulic simulations to investigate the regional groundwater flow in the Upper Rhine Graben. The modeling is based on an existing detailed 3-D structural model covering the whole Upper Rhine Graben from the surface down to 14 km of depth. The overall goal of this study is to provide some quantitative analysis on the role of the hydraulic head topology in shaping the underground hydrodynamics by taking into account interactions with the heterogeneous subsurface sedimentary configuration of the basin system. Therefore, the main question addressed by this study can be summarized as follows: does the deep graben flow follow the topographic gradient and the flow direction of the river Rhine from the Alps northward to the northernmost area of the Upper Rhine Graben? Our results demonstrate the presence of a regional subsurface flow in the sedimentary rocks aligning from the graben flanks towards its center and in the southern half of the graben from south to north. The graben-parallel flow velocity is found to be about 1 order of magnitude lower than the velocity predicted perpendicular to the main graben axis. Besides these general trends, the modeling highlights local heterogeneities in the shallow 3-D flow field. Those arise from the interaction between regional groundwater flow and the heterogeneous sedimentary configuration. Within the Cenozoic sediments forming the uppermost aquifer in the model, groundwater flows are driven by imposed hydraulic gradients from recharge areas located at higher elevations in the Black Forest and Vosges Mountains to the discharge region at a lower elevation in the Rhine valley. The presence of a regional aquitard (Keuper) separating the shallow and the deeper aquifer system (Muschelkalk, Buntsandstein, and Rotliegend) hinders hydraulic connection among the two aquifer systems. This is exemplified by the development of a flow system in the deeper aquifers, which shows a more continuous graben-parallel south–north direction. Based on these results we can conclude that both the hydraulic head topology and the level of structuration of the sedimentary sequence exert a 1st-order role in shaping the regional flow system at depth. The regional model predicts a heterogeneous flow system within the upper 4 km of the Upper Rhine Valley, where flow velocities in the graben valley can reach up to 45 mm yr−1 in the upper and lower aquifers. Back to the current conceptual hydrogeological model, the results question the presence of a graben through northward flow, being limited to the southern half of the graben. In the north, the groundwater dynamics turn out to be more complex, being structurally linked to the local geology. This calls for additional studies with a higher level of both structural and stratigraphic attributes in order to arrive at a better quantification of the local to the regional groundwater dynamics in the area.
Knowledge of groundwater flow is of high relevance for groundwater management or the planning of different subsurface utilizations such as deep geothermal facilities. While numerical models can help to understand the hydrodynamics of the targeted reservoir, their predictive capabilities are limited by the assumptions made in their setup. Among others, the choice of appropriate hydraulic boundary conditions, adopted to represent the regional to local flow dynamics in the simulation run, is of crucial importance for the final modelling result. In this work, we systematically address this problematic in the area of the central part of the Upper Rhine Graben. We quantify how and to which degree different upper boundary conditions and vertical cross-boundary fluid movement influence the calculated deep fluid flow conditions in the area under study. Robust results, which are insensitive to the choice of boundary condition, are: (i) a regional groundwater flow component descending from the graben shoulders to rise at its centre and (ii) the presence of heterogeneous hydraulic potentials at the rift shoulders. Contrarily, results affected by the chosen boundary conditions are: (i) calculated flow velocities, (ii) the absolute position of the upflow axis, and (iii) the evolving local flow dynamics. If, in general, the investigated area is part of a supra-regional flow system—like the central Upper Rhine Graben is part of the entire Upper Rhine Graben—the inflow and outflow across vertical model boundaries need to be considered.
One key aspect in the energy transition is to use the deep geothermal energy stored in sedimentary basins as well as in igneous and metamorphic basement rocks. To estimate the variability of deep geothermal potentials across different geological domains as encountered in the Federal State of Hesse (Germany), it is necessary to understand the driving processes of fluid flow and heat transport affecting subsurface temperature variations. In this study, we quantify the stored energy in a set of geological units in the subsurface of Hesse with the method of “heat in place” (HIP, sensu Muffler and Cataldi in Geothermics 7:53–89, 1978)—HIP is one proxy for the geothermal potential of these units controlled by their temperature configuration as derived from a series of coupled 3D thermo-hydraulic numerical models. We show how conductive, advective and convective heat transport mechanisms influence the thermal field and thereby the HIP calculations. The heterogeneous geology of the subsurface of Hesse ranges from locally outcropping Paleozoic basement rocks to up to 3.8 km thick Cenozoic, porous sedimentary deposits in the tectonically active northern Upper Rhine Graben. The HIP was quantified for five sedimentary layers (Cenozoic, Muschelkalk, Buntsandstein, Zechstein, Rotliegend) as well as for the underlying basement. We present a set of maps allowing to identify geothermally prospective subregions of Hesse based on the laterally varying thermal energy stored within the units. HIP is predicted to be highest in the area of the northern Upper Rhine Graben in the Cenozoic unit with up to 700 GJ $$\text {m}^{-2}$$ and in the Rotliegend with up to 617 GJ $$\text {m}^{-2}$$ . The calculations account for the variable thicknesses and temperatures of the layers, density and heat capacity of the solid and fluid parts of the rocks as well as porosity.
This study investigates the feasibility to repurpose wells from gas production for geothermal closed-loop application in the North German Basin (NGB). The objective for this research topic is to extend the value-added chain of idle wells by re-completion as coaxial deep borehole heat exchangers as an efficient way to produce green energy without drilling new wells by saving the carbon emission and costs of building a new geothermal well. With numerical models of two typical geological settings of the NGB and two different completion schemes, it is possible to simulate the thermal performance over a lifetime of 30 years. The calculated heat extraction rates range from 200 to 400 kW, with maximum values of up to 600 kW. Sensitivity analyses demonstrate that re-completion depth and injection temperature are the most sensitive parameters of thermal output determination. The heat demand around the boreholes is mapped, and heat generation costs are calculated with heating network simulations. The initial production costs for heat are comparable to other renewable energy resources like biomass and competitive against gas prices in 2022. This study highlights available geothermal resources’ environmental and economic potential in already installed wells. The application has almost no geological and no drilling risks and may be installed at any idle well location.