NOTICE: This is the author’s version of a work that was accepted for publication in the journal Colloids and Surfaces A: Physicochemical and Engineering Aspects. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published at: http://dx.doi.org/10.1016/j.colsurfa.2014.03.033Dried blood spotting (DBS) is a convenient blood collecting and sampling method which is widely applied in newborn screening and blood analysis. At the moment, the practice is to try to keep the blood within a marked circle in a thin porous filter paper. However, it is not always possible to predict exactly how the blood spot spreads inside the filter papers and it depends on many factors including the properties of the filter papers, blood properties and how the blood is deposited on the filter paper. In this paper, we aim to identify the relationships between the physical properties and the spreading behaviour of blood on a typical DBS filter paper (Whatman 903). Pig’s blood was used to mimic the behaviour of human blood and investigate the spreading/imbibition processes of blood drops on the filter paper. Both top and side views were used to analyse the spreading/imbibition behaviour. The experimental data present the haematocrit effect on the spreading dynamics of blood for dried blood spot sampling. The results obtained prove that the spreading/imbibition time dependences of droplet height, droplet base radius and contact angle are universal function of dimensionless time
1 May 2015 in Journal of Colloid and Interface Science
The process of dried blood spot sampling involves simultaneous spreading and penetration of blood into a porous filter paper with subsequent evaporation and drying. Spreading of small drops of blood, which is a non-Newtonian liquid, over a dry porous layer is investigated from both theoretical and experimental points of view. A system of two differential equations is derived, which describes the time evolution of radii of both the drop base and the wetted region inside the porous medium. The system of equations does not include any fitting parameters. The predicted time evolutions of both radii are compared with experimental data published earlier. For a given power law dependency of viscosity of blood with different hematocrit level, radii of both drop base and wetted region, and contact angle fell on three universal curves if appropriate scales are used with a plot of the dimensionless radii of the drop base and the wetted region inside the porous layer and dynamic contact angle on dimensionless time. The predicted theoretical relationships are three universal curves accounting satisfactorily for the experimental data.
1 September 2016 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
This paper was accepted for publication in the journal Colloids and Surfaces A: Physicochemical and Engineering Aspects and the definitive published version is available at http://dx.doi.org/10.1016/j.colsurfa.2015.10.056The sampling process of dried blood spot (DBS) is spreading of blood, which is Non-Newtonian fluid, over porous substrates. Spreading/imbibition behaviour of blood samples over Whatman 903 filter paper in complete wetting case has been investigated earlier (Tzu Chieh Chao et al., 2015). The spreading behaviour of DBS sampling has been investigated below in the case of partial wetting. Nitrocellulose membranes (NCM) with different pore size and silanized Whatman 903 blood saving card have been used as porous substrates. The spreading experiments have been applied to obtain the time evolution of spreading parameters, such as, radius of droplet base, dynamic contact angle and radius of the wetted region. The result of spreading on NCM showed that the spreading process was a partial wetting spreading. A separation of red blood cells (RBCs) and blood plasma has been found in the case of the blood drop spreading over 0.2 and 3.0 μm NCMs. Important that while the RBCs were not damaged in this process. This opens a completely new opportunity to (1) investigate RBCs and plasma separately; (2) to use this method for non-destructive separation of living cells from aqueous solution
NOTICE: this is the author’s version of a work that was accepted for publication in \ud Chemical Engineering Journal. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Chemical Engineering Journal, 259, pp. 961-971, DOI: 10.1016/j.cej.2014.08.077Rotating bioreactor, such as the NASA bioreactor, which was designed by the National Aeronautics and Space Administration (NASA), USA, can be used to mimic micro-gravity conditions and simulate the effects of microgravity on cells growth. The cell growth in the bioreactor depends on the nutrient availability which in turn depends on the cell density and distribution within the bioreactor. In this work, we use a numerical model of suspended particle motion to simulate the cell motion and distribution in a specific variant of the NASA bioreactor, namely, the high aspect ratio vessel (HARV) bioreactor. The nutrient distribution in the bioreactor is simulated based on a convection-diffusion-reaction supplemented by laboratory experiments aimed at obtaining the required data. We present the modelling framework in this paper and discuss the most salient simulated results. For example, the simulation results show that the distributions of the cells in the bioreactor appear as concentric circles and that the cells density is higher in the middle of the HARV bioreactor. These cell distributions imply that they may accumulate in the middle of the bioreactor at sufficiently high cell density. The results also demonstrate that the concentration of nutrient is fairly uniform in the bioreactor but decreases slightly from the outer radius of the HARV bioreactor to the inner radius. This is possibly caused by the higher consumption of glucose due to the higher cell density in the middle of the radius. We expect that the modelling framework in this paper would help optimize the culture conditions for the cells in HARV bioreactors