Paper presents the results of factorial experiments made to establish the influence of technological parameters of 3D printing using the Fused Deposition Modeling (FDM) Technology, on the mechanical properties of the material deposited with ULTRA PLA filaments. By planning the experiments and the statistical processing of the results, mathematical relations were established regarding the dependence between the objective functions, the controllable factors and their interactions. To obtain high tensile strengths of the components made by 3D printing, regimes are required to allow the deposition of layers as thin as possible (h = 0.1 mm) and temperatures as high as possible, close to 300°C. The choice of inappropriate values of these process parameters can lead to a significant decrease in tensile strength, reaching even up to 30-40% of the maximum possible value to be reached. The experiments reveal that the printing speed does not have a major influence on the mechanical properties. Practical, the printing speed is limited by the technical characteristics of the printer used. The results of the experimental research obtained on a number of 30 process variants led to the establishment of optimal 3D printing variants that correspond to the requirements imposed on the objectively analysed functions (tensile strength, dimensional accuracy, speed of execution, surface quality).
This paper presents the effect of saline environment on the fatigue behaviour of high-velocity oxygen fuel thermal-sprayed WC–CrC–Ni coatings. These coatings are used to improve the surface hardness, corrosion and wear resistance of components or products, in the place of hard chrome plating. Although so far many tests on the wear and corrosion of coating behaviour were carried, the conduct of the joint action fatigue – a corrosive environment is not fully identified. In the frame of the experimental programme, similar axial fatigue tests at room temperature, on air or on specimens immersed in 3% NaCl solution and also chemical composition, structural analysis of the fracture surface were performed, using SEM and EDX. The saline environmentcauses material corrosion, generation of voids and microcracks on the specimen surface and their propagation through the specimen cross-section, accelerating the specimen failure.
The purpose of this research is to meet current technical and ecological challenges by developing novel steel coating systems specifically designed for mechanical equipment used in aggressive acid conditions. Homogeneous sandwich-type layered films on the surface of steel electrodes were realized using a pseudo-binary oxide, MnTa2O6, and two different substituted porphyrin derivatives, namely: 5-(4-carboxy-phenyl)-10,15,20-tris (4-methyl-phenyl)-porphyrin and 5-(4-methyl-benzoate)-10,15,20-tris (4-methyl-phenyl)-porphyrin, which are novel investigated compound pairs. Two suitable laser strategies, pulsed laser deposition (PLD) and matrix-assisted pulsed laser evaporation (MAPLE), were applied in order to prevent porphyrin decomposition and to create smooth layers with low porosity that are extremely adherent to the surface of steel. The electrochemical measurements of corrosion-resistant coating performance revealed that in all cases in which the steel electrodes were protected, a significant value of corrosion inhibition efficiency was found, ranging from 65.6 to 83.7%, depending on the nature of the porphyrin and its position in the sandwich layer. The highest value (83.7%) was obtained for the MAPLE/PLD laser deposition of 5-(4-carboxy-phenyl)-10,15,20-tris (4-methyl-phenyl)-porphyrin/MnTa2O6(h), meaning that the inhibitors adsorbed and blocked the access of the acid to the active sites of the steel electrodes.
The use of graphene (Gr) and its derivates graphene oxide (GO) showed that these materials are good candidates to enhance the properties of polyurethane (PU) coatings, especially the anticorrosion ones since graphene absorbs most of the light and provides hydrophobicity for repelling water. An important aspect of these multifunctional materials is that all these improvements can be realized even at very low filler loadings in the polymer matrix. In this work, an ultrasound cavitation technique was used for the proper dispersion of GO nanosheets (GON) in polyurethane (PU) resin to obtain a composite coating to protect the AlMg3 substrate. The addition of GON considerably improved the physical properties of coatings, as demonstrated by electrochemical impedance spectroscopy (EIS) analysis, promising improved anticorrosion performance after accelerated UV-ageing. Computational methods and Differential Scanning Calorimetry (DSC) measurements showed that GON facilitates the formation of additional bonds and stabilizes the PU structures during the ultraviolet (UV) exposure and aggressive attack of corrosive species. Limiting oxygen index (LOI) data reveal a slow burning behaviour of PU-GON coatings during UV exposure, which is better than PU alone.