Through-silicon vias (TSVs) filled with densified and transferred carbon nanotube (CNT) forests are experimentally demonstrated. The filling is achieved by a postgrowth low-temperature transfer process at 200 instead of direct CNT growth in the vias normally requiring high temperature. A vapor densification method is also applied to densify the as-grown CNT forests, which allows for packing more CNTs in the vias to reduce their resistances. CNT-filled TSVs fabricated based on these two key steps show CMOS compatibility and roughly one order of magnitude reduction in resistivity compared to the TSVs filled with as-grown undensified CNT forests.
Transistors operating at high frequencies are the basic building blocks of millimeter-wave communication and sensor systems. The high charge-carrier mobility and saturation velocity in graphene can open way for ultra-fast field-effect transistors with a performance even better than what can be achieved with III-V-based semiconductors. However, the progress of high-speed graphene transistors has been hampered by fabrication issues, influence of adjacent materials, and self-heating effects. Here, we report on the improved performance of graphene field-effect transistors (GFETs) obtained by using a diamond substrate. An extrinsic maximum frequency of oscillation ${f}_{{\mathrm {max}}}$ of up to 54 GHz was obtained for a gate length of 500 nm. Furthermore, the high thermal conductivity of diamond provides an efficient heat-sink, and the relatively high optical phonon energy of diamond contributes to an increased charge-carrier saturation velocity in the graphene channel. Moreover, we show that GFETs on diamond exhibit excellent scaling behavior for different gate lengths. These results promise that the GFET-on-diamond technology has the potential of reaching sub-terahertz frequency performance.
8 January 2021 in IEEE Transactions on Electron Devices
The high-frequency performance of top-gated graphene field-effect transistors (GFETs) depends to a large extent on the saturation velocity of the charge carriers, a velocity limited by inelastic scattering by surface optical phonons from the dielectrics surrounding the channel. In this work, we show that, by simply changing the graphene channel surrounding dielectric with a material having higher optical phonon energy, one could improve the transit frequency and maximum frequency of oscillation of GFETs. We fabricated GFETs on conventional SiO 2 /Si substrates by adding a thin Al 2 O 3 interfacial buffer layer on top of SiO 2 /Si substrates, a material with about 30% higher optical phonon energy than that of SiO 2 , and compared performance with that of GFETs fabricated without adding the interfacial layer. From S-parameter measurements, a transit frequency and a maximum frequency of oscillation of 43 and 46 GHz, respectively, were obtained for GFETs on Al 2 O 3 with 0.5- $\mu \text{m}$ gate length. These values are approximately 30% higher than those for state-of-the-art GFETs of the same gate length on SiO 2 . For relating the improvement of GFET high-frequency performance to improvements in the charge carrier saturation velocity, we used standard methods to extract the charge carrier velocity from the channel transit time. A comparison between two sets of GFETs with and without the interfacial Al 2 O 3 layer showed that the charge carrier saturation velocity had increased from $1.5\cdot 10^{{7}}$ to $2\cdot 10^{{7}}$ cm/s.
30 April 2021 in IEEE Transactions on Electron Devices
Accurate device models and parameter extraction methods are of utmost importance for characterizing graphene FETs (GFETs) and for predicting their performance in circuit applications. For dc characterization, accurate extraction of mobility and series resistance is of particular concern. In this article, we show how a first-order mobility degradation model can be used to separate information about mobility degradation and series resistance for a set of GFETs of different channel lengths. Data from a large set of top-gated GFETs based on chemical vapor deposited (CVD) graphene was analyzed to validate the proposed model and extraction procedures. For removing any uncertainties caused by the observed device-to-device data variations due to the uneven quality of CVD graphene, the same methods were applied to a set of closely located bottom-gated GFETs found in literature. Those GFETs were designed for transfer length methods and fabricated on exfoliated graphene of homogeneous quality. Similar mobility degradation behavior was observed for both sets of devices with the mobility being reduced to half for a voltage-induced charge carrier density of 10 13 cm -2 .
In many applications like sensors, displays, and defoggers, there is a need for transparent and efficient heater elements produced at low cost. For this reason, we evaluated the performance of graphene-based heaters with from one to five layers of graphene on flexible and transparent polyethylene terephthalate (PET) substrates in terms of their electrothermal properties like heating/cooling rates and steady-state temperatures as a function of the input power density. We found that the heating/cooling rates followed an exponential time dependence with a time constant of just below 6 s for monolayer heaters. From the relationship between the steady-state temperatures and the input power density, a convective heat-transfer coefficient of 60 W·m−2·°C−1 was found, indicating a performance much better than that of many other types of heaters like metal thin-film-based heaters and carbon nanotube-based heaters.