To construct large-scale silicon electro-optical switches for optical interconnections, we developed a method using a limited number of power monitors inserted at certain positions to detect and determine the optimum operating points of all switch units to eliminate non-uniform effects arising from fabrication errors. We also introduced an optical phase bias to one phase-shifter arm of a Mach–Zehnder interferometer (MZI)-type switch unit to balance the two operation statuses of a silicon electro-optical switch during push–pull operation. With these methods, a 32 × 32 MZI-based silicon electro-optical switch was successfully fabricated with 180-nm complementary metal–oxide–semiconductor (CMOS) process technology, which is the largest scale silicon electro-optical switch to the best of our knowledge. At a wavelength of 1520 nm, the on-chip insertion losses were 12.9 to 16.5 dB, and the crosstalk ranged from −17.9 to −24.8 dB when all units were set to the ‘Cross’ status. The losses were 14.4 to 18.5 dB, and the crosstalk ranged from −15.1 to −19.0 dB when all units were in the ‘Bar’ status. The total power consumptions of the 32 × 32 switch were 247.4 and 542.3 mW when all units were set to the ‘Cross’ and ‘Bar’ statuses, respectively.
We propose and experimentally demonstrate broadband silicon mode (de)multiplexers based on the optimization of system adiabaticity using shortcuts to adiabaticity (STA). The measured insertion losses and crosstalks were less than 1.1 dB and −24 dB, respectively, for the five two-mode mode-division-multiplexing (MDM) links over wavelengths ranging from 1500 nm to 1600 nm. The four-mode MDM link showed measured insertion losses and crosstalks less than 1.3 dB and −23 dB, respectively, within the same wavelength range. The method paves the way for future adaptation of the STA protocols to various components.
We experimentally demonstrate two types of programmable, low-threshold, optically controlled nonlinear activation functions, which are challenging to realize in photonic neural networks (PNNs). These devices rely on on-chip integrated Ge–Si photoelectric detectors and silicon electro-optical switches, and they generate rectified linear unit (ReLU) or sigmoid functions with arbitrary slopes without additional electrical processing. Both devices function at an extremely low threshold of 0.2 mW. The embedding of these nonlinear activation functions into convolutional neural networks facilitates the attainment of high inference accuracies of up to 95% when applied to Modified National Institute of Standards and Technology (MNIST) handwritten digit-classification tasks. The devices are suitable for low-power PNNs with an arbitrary number of propagation layers in photonic-computing chips.
Frequency-modulated continuous wave (FMCW) light detection and ranging (lidar) is a promising solution for three-dimensional (3D) imaging and autonomous driving. This technique maps range and velocity measurement to frequency counting via coherent detection. Compared with single-channel FMCW lidar, multi-channel FMCW lidar can greatly improve the measurement rate. A chip-scale soliton micro-comb is currently used in FMCW lidar to enable multi-channel parallel ranging and significantly increase the measurement rate. However, its range resolution is limited due to the soliton comb having only a few-GHz frequency sweep bandwidth. To overcome this limitation, we propose using a cascaded modulator electro-optic (EO) frequency comb for massively parallel FMCW lidar. We demonstrate a 31-channel FMCW lidar with a bulk EO frequency comb and a 19-channel FMCW lidar using an integrated thin-film lithium niobate (TFLN) EO frequency comb. Both systems have a sweep bandwidth of up to 15 GHz for each channel, corresponding to a 1-cm range resolution. We also analyze the limiting factors of the sweep bandwidth in 3D imaging and perform 3D imaging for a specific target. The measurement rate achieved is over 12 megapixels per second, which verifies its feasibility for massively parallel ranging. Our approach has the potential to greatly benefit 3D imaging in fields where high range resolution is required, such as in criminal investigation and precision machining.
Polarization splitter-rotators (PSRs) are crucial components for controlling the polarization states of the input light in photonic integrated circuits. In this paper, we designed, fabricated and characterized a high-performance CMOS-compatible O-band PSR based on silicon-on-insulator (SOI) platform by using inverse design technique. The PSR mainly consists of a polarization rotator designed by our new proposed bi-level shape adjoint method and a mode demultiplexer designed by topology adjoint method. The device robustness against fabrication errors is significantly strengthened by properly designing optimization strategies. The proposed PSR displays a low insertion loss (<1dB) and low crosstalk (<−20 dB) within a bandwidth of 50 nm by measurements. The device footprint is 3×17 µm, making this the smallest PSR based on standard silicon photonic platforms with no extra layers or an air cladding.
We proposed and experimentally demonstrated a compact, broadband, and low-loss-mode-evolution-based coupler on a silicon-on-insulator platform. The waveguide widths and separations of the coupler were tapered in an optimal manner using the shortcuts to the adiabaticity method. The coupler, with a total length and 200 nm feature size, exhibited measured excess loss over a broadband wavelength range from 1500 to 1600 nm. Balanced and unbalanced Mach–Zehnder interferometers fabricated for validation showed extinction ratios larger than 27 and 23 dB, respectively, over a 100 nm bandwidth. The extracted splitting ratio was between 0.48 and 0.52.