The combustion emissions of the hydrogen-fueled engines are very clean, but the problems of abnormal combustion and high NOx emissions limit their applications. Nowadays hydrogen engines use exhaust gas recirculation (EGR) technology to control the intensity of premixed combustion and reduce the NOx emissions. This study aims at improving the abnormal combustion and decreasing the NOx emissions of the hydrogen engine by applying a three-dimensional (3D) computational fluid dynamics (CFD) model of a single-cylinder hydrogen-fueled engine equipped with an EGR system. The results indicated that peak in-cylinder pressure continuously increased with the increase of the ignition advance angle and was closer to the top dead center (TDC). In addition, the mixture was burned violently near the theoretical air–fuel ratio, and the combustion duration was shortened. Moreover, the NOx emissions, the average pressure, and the in-cylinder temperature decreased as the EGR ratio increased. Furthermore, increasing the EGR ratio led to an increase in the combustion duration and a decrease in the peak heat release rate. EGR system could delay the spontaneous combustion reaction of the end-gas and reduce the probability of knocking. The pressure rise rate was controlled and the in-cylinder hot spots were reduced by the EGR system, which could suppress the occurrence of the pre-ignition in the hydrogen engine.

The continuous increase in the number of stringent exhaust emission legislations of marine Diesel engines had led to a decrease in NO_x emissions at the required level. Selective catalyst reduction (SCR) is the most prominent and mature technology used to reduce NO_x emissions. However, to obtain maximum NO_x removal with minimum ammonia slip remains a challenge. Therefore, new mixers are designed in order to obtain the maximum SCR efficiency. This paper reports performance parameters such as uniformity of velocity, ammonia uniformity distribution, and temperature distribution. Also, a numerical model is developed to investigate the interaction of urea droplet with exhaust gas and its effects by using line (LM) and swirl (SM) type mixers alone and in combination (LSM). The urea droplet residence time and its interaction in straight pipe are also investigated. Model calculations proved the improvement in velocity uniformity, distribution of ammonia uniformity, and temperature distribution for LSM. Prominent enhancement in the evaporation rate was also achieved by using LSM, which may be due to the breaking of urea droplets into droplets of smaller diameter. Therefore, the SCR system accomplished higher urea conversion efficiency by using LSM. Lastly, the ISO 8178 standard engine test cycle E3 was used to verify the simulation results. It has been observed that the average weighted value of NO_x emission obtained at SCR outlet using LSM was 2.44 g/kWh, which strongly meets International Maritime Organization (IMO) Tier III NO_x (3.4 g/kWh) emission regulations.

Injection timing variations have a significant effect on the performance and pollutant formation in diesel engines. Numerical study was conducted to investigate the impact of injection timing on engine performance and pollutants in a six-cylinder turbocharged diesel engine. Diesel fuel with different amounts (5%, 15%, and 25% by volume) of n-butanol was used. Simulations were performed at four distinct injection timings (5°, 10°, 20°, 25°CA bTDC) and two distinct loads of brake mean effective pressure (BMEP = 4.5 bar and 10.5 bar) at constant engine speed (1800 rpm) using the GT-Power computational simulation package. The primary objective of this research is to determine the optimum injection timing and optimum blending ratio for improved efficiencies and reduced emissions. Notable improvements in engine performance and pollutant trends were observed for butanol-diesel blends. The addition of butanol to diesel fuel has greatly diminished NO_X and CO pollutants but it elevated HC and CO₂ emissions. Retarded injection timing decreased NO_X and CO₂ pollutants while HC and CO₂ emissions increased. The results also indicated that early injection timings (20°CA bTDC and 25°CA bTDC) lowered both CO₂ and unburned hydrocarbon emissions. Moreover, advanced injection timing slightly improved brake thermal efficiency (BTE) for all engine loads. It is concluded that retarded injection timing, i.e., 10°CA bTDC demonstrated optimum results in terms of performance, combustion and emissions and among the fuels 15B showed good outcome with regard to BTE, higher heat release rate, and lower pollution of HC, CO, and NOx.