In a wide range of fluid machinery, a turbulent boundary layer can be exposed to rapid transients of the freestream conditions. A simplified model of the boundary layer response would provide valuable guidance in understanding these situations in multiple engineering applications. To this end, a turbulent boundary flow, subject to freestream acceleration, was explored through high-fidelity simulations and Reynolds-averaged Navier–Stokes calculations. Test cases were considered in which the flow over a flat plate accelerated from Mach 0.3 up to 0.6 over two time scales, 10 ms and 25 ms. Based on data from the calculations, the integral boundary layer momentum equation was simplified to propose a new reduced-order model capable of computing the evolution of the boundary layer under external flow transients. Given the initial boundary layer height, and the temporal evolution of the freestream pressure, velocity, and density, the model predicts the transient development of the boundary layer. With the transient boundary layer profile known, the temporal history of the skin friction and heat transfer can be predicted, taking advantage of standard shear stress correlations and the Reynolds analogy.
7 September 2018 in Journal of Engineering for Gas Turbines and Power
The aerothermal performance of the low-pressure turbine in unmanned aerial vehicles is significantly abated at high altitude, due to boundary layer separation. Different flow control strategies have been proposed to prevent boundary layer separation, such as dielectric barrier discharges (DBD) and synthetic jets. However, the optimization of the control approach requires a better characterization of the separated regions at transient conditions. The present investigation analyzes the behavior of separated flows, reporting the inception and separation length, allowing the development of efficient flow control methods under nontemporally uniform inlet conditions. The development of separated flows was investigated with numerical simulations including Unsteady Reynolds average Navier–Stokes (URANS) and large Eddy simulations (LES). The present research was performed on a wall-mounted hump, which imposes a pressure gradient representative of the suction side of low pressure turbines. Through sudden flow accelerations, we looked into the dynamic response of the shear layer detachment as it is modulated by the mean flow evolution. Similarly, we studied the behavior of the recirculation bubble under periodic disturbances imposed at various frequencies ranging from 10 to 500 Hz, at which the Reynolds number oscillates between 40,000 and 180,000. As a first step into the flow control, we added a slot to allow flow injection and ingestion upstream of the separation inception. Exploring the behavior of the separated region at different conditions, we defined the envelope for its periodic actuation. We found that by matching the actuator frequency with the frequency response of the separated region, the performance of the actuation is boosted.
1 August 2021 in Experimental Thermal and Fluid Science
The behavioural characteristics of thermal boundary layer inception dictate the efficiency of heat exchangers and the operational limits of fluid machinery. The specific time required by the thermal boundary layer to be established is vital to optimize flow control strategies, as well as the thermal management of systems exposed to ephemeral phenomena, typically on the millisecond scale. This paper presents the time characterization of the momentum and thermal boundary layer development in transient turbulent compressible air flows. We present a new framework to perform such estimations based on detailed unsteady Reynolds averaged Navier–Stokes simulations that may be extended to higher fidelity simulations. First of all, the aerodynamic boundary layer initiation is described using adiabatic simulations. Additional numerical calculations were then performed by setting the isothermal wall condition to evaluate the additional time required by the thermal boundary layer to establish after the aerodynamic boundary layer reaches its steady state. Finally, full conjugate simulations were executed to compute the warm up effect of the solid during the blowdown of a hot fluid over a colder metallic test model. The transient performance of the turbulent thermal and momentum boundary layers is quantified through numerical simulations of air blowdown over a flat plate for different mainstream flow conditions. The effects of Reynolds number, free stream velocity, transient duration, test article length and free stream temperature were independently assessed, to then define a mathematical expression of the momentum boundary layer settlement. This paper presents a novel numerical correlation of the additional time required by the thermal boundary layer to be stablished after the settlement of the momentum boundary layer. The time scales of the aerodynamic and thermal boundary layers are presented as a function of relevant non-dimensional numbers, as well as the description of the response of the near wall flow to sudden free stream changes. The characterization of the boundary layer mechanisms discussed in this paper contribute to the establishment of an evidence-based foundation for advances in the field of flow control.
1 June 2021 in Flow Measurement and Instrumentation
This study represents a novel evaluation of active flow control to alleviate the aerothermal penalties created by the blunt fin-induced shock wave–boundary layer interaction. The manuscript analyzes the effect of flow injection on a blunt fin-induced shock wave–boundary layer interaction via computational fluid dynamics simulations with various degrees of resolution. The impact on the mean flow topology and wall variables was investigated utilizing Reynolds-averaged Navier–Stokes simulations. Detached-eddy simulations revealed the low-frequency shock motion, shock wave–boundary layer, and horseshoe vortex interaction. The test article was exposed to two different incoming boundary layer thicknesses; the thicker boundary layer led to the appearance of larger turbulent scales. The Detached-eddy simulations revealed the time history of the shock wave–boundary layer interaction, focusing on the inception and development of the recirculated flow regions. Ultimately, spectral proper orthogonal decomposition was employed to identify the structures associated with the low-frequency shock motion caused by the shock wave–boundary layer interaction.