Conservation of energy is used to derive a thermodynamically-consistent contact angle, θt, when fluid phase 1 displaces phase 2 in a porous medium. Assuming no change in Helmholtz free energy between two local equilibrium states we find that Δa1scosθt=κϕΔS1+Δa12, where a is the interfacial area per unit volume, ϕ is the porosity, S is the saturation and κ the curvature of the fluid-fluid interface. The subscript s denotes the solid, and we consider changes, Δ, in saturation and area. With the advent of high-resolution time-resolved three-dimensional X-ray imaging, all the terms in this expression can be measured directly. We analyse imaging datasets for displacement of oil by water in a water-wet and a mixed-wet sandstone. For the water-wet sample, the curvature is positive and oil bulges into the brine with almost spherical interfaces. In the mixed-wet case, larger interfacial areas are found, as the oil resides in layers. The mean curvature is close to zero, but the interface tends to bulge into brine in one direction, while brine bulges into oil in the other. We compare θt with the values measured geometrically in situ on the pore-scale images, θg. The thermodynamic angle θt provides a robust and consistent characterization of wettability. For the water-wet case the calculated value of θt gives an accurate prediction of multiphase flow properties using pore-scale modelling.
1 September 2021 in International Journal of Greenhouse Gas Control
To examine the need to incorporate in situ wettability measurements in direct numerical simulations, we compare waterflooding experiments in a mixed-wet carbonate from a producing reservoir and results of direct multiphase numerical simulations using the color-gradient lattice Boltzmann method. We study the experiments of Alhammadi et al. (Sci Rep 7(1):10753, 2017 . https://doi.org/10.1038/s41598-017-10992-w ) where the pore-scale distribution of remaining oil was imaged using micro-CT scanning. In the experiment, in situ contact angles were measured using an automated algorithm (AlRatrout et al. in Adv Water Resour 109:158–169, 2017 . https://doi.org/10.1016/j.advwatres.2017.07.018 ), which indicated a mixed-wet state with spatially non-uniform angles. In our simulations, the pore structure was obtained from segmented images of the sample used in the experiment. Furthermore, in situ measured angles were also incorporated into our simulations using our previously developed wetting boundary condition (Akai et al. in Adv Water Resour 116(March):56–66, 2018 . https://doi.org/10.1016/j.advwatres.2018.03.014 ). We designed six simulations with different contact angle assignments based on experimentally measured values. Both a constant contact angle based on the average value of the measured values and non-uniform contact angles informed by the measured values gave a good agreement for fluid pore occupancy between the simulation and the experiment. However, the constant contact angle assignment predicted 54% higher water effective permeability after waterflooding than that estimated for the experimental result, whereas the non-uniform contact angle assignment gave less than 1% relative error. This means that to correctly predict fluid conductivity in mixed-wet rocks, a spatially heterogeneous wettability state needs to be taken into account. The novelty of this work is to provide a direct pore-scale comparison between experiments and simulations employing experimentally measured contact angles, and to demonstrate how to use measured contact angle data to improve the predictability of direct numerical simulation, highlighting the difference between the contact angle required for the simulation of dynamic displacement process and the contact angle measured at equilibrium after waterflooding.
1 April 2020 in Journal of Colloid and Interface Science
The change of wettability toward more water-wet by the injection of low salinity water can improve oil recovery from porous rocks, which is known as low salinity water flooding. To simulate this process at the pore-scale, we propose that the alteration in surface wettability mediated by thin water films which are below the resolution of simulation grid blocks has to be considered, as observed in experiments. This is modeled by a wettability alteration model based on rate-limited adsorption of ions onto the rock surface. The wettability alteration model is developed and incorporated into a lattice Boltzmann simulator which solves both the Navier-Stokes equation for oil/water two-phase flow and the advection-diffusion equation for ion transport. The model is validated against two experiments in the literature, then applied to 3D micro-CT images of a rock. Our model correctly simulated the experimental observations caused by the slow wettability alteration driven by the development of water films. In the simulations on the 3D rock pore structure, a distinct difference in the mixing of high and low salinity water is observed between secondary and tertiary low salinity flooding, resulting in different oil recoveries.