Amer Mohamed Alhammadi

Amer Mohamed Alhammadi

Auto-generated profile, based on publicly available information

Amer Mohamed Alhammadi

Imperial College London

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 September 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
AAAmer M. Alhammadi
Amer M. Alhammadi
AAAhmed AlRatrout
Ahmed AlRatrout
KSKamaljit Singh
Kamaljit Singh
BBBranko Bijeljic
Branko Bijeljic
MBMartin J. Blunt
Martin J. Blunt
We used X-ray micro-tomography to image the in situ wettability, the distribution of contact angles, at the pore scale in calcite cores from a producing hydrocarbon reservoir at subsurface conditions. The contact angle was measured at hundreds of thousands of points for three samples after twenty pore volumes of brine flooding.We found a wide range of contact angles with values both above and below 90°. The hypothesized cause of wettability alteration by an adsorbed organic layer on surfaces contacted by crude oil after primary drainage was observed with Scanning Electron Microscopy (SEM) and identified using Energy Dispersive X-ray (EDX) analysis. However, not all oil-filled pores were altered towards oil-wet conditions, which suggests that water in surface roughness, or in adjacent micro-porosity, can protect the surface from a strong wettability alteration. The lowest oil recovery was observed for the most oil-wet sample, where the oil remained connected in thin sheet-like layers in the narrower regions of the pore space. The highest recovery was seen for the sample with an average contact angle close to 90°, with an intermediate recovery in a more water-wet system, where the oil was trapped in ganglia in the larger regions of the pore space.

23 November 2018 in Transport in Porous Media
Verified
Journal Article
Open access
PDF file
TATakashi Akai
Takashi Akai
AAAmer M. Alhammadi
Amer M. Alhammadi
MBMartin J. Blunt
Martin J. Blunt
BBBranko Bijeljic
Branko Bijeljic
To examine the need to incorporate in situ wettability measurements in direct numerical simulations, we compare waterflooding experiments in a mixed-wet carbonate from a producing reservoir and results of direct multiphase numerical simulations using the color-gradient lattice Boltzmann method. We study the experiments of Alhammadi et al. (Sci Rep 7(1):10753, 2017 . https://doi.org/10.1038/s41598-017-10992-w ) where the pore-scale distribution of remaining oil was imaged using micro-CT scanning. In the experiment, in situ contact angles were measured using an automated algorithm (AlRatrout et al. in Adv Water Resour 109:158–169, 2017 . https://doi.org/10.1016/j.advwatres.2017.07.018 ), which indicated a mixed-wet state with spatially non-uniform angles. In our simulations, the pore structure was obtained from segmented images of the sample used in the experiment. Furthermore, in situ measured angles were also incorporated into our simulations using our previously developed wetting boundary condition (Akai et al. in Adv Water Resour 116(March):56–66, 2018 . https://doi.org/10.1016/j.advwatres.2018.03.014 ). We designed six simulations with different contact angle assignments based on experimentally measured values. Both a constant contact angle based on the average value of the measured values and non-uniform contact angles informed by the measured values gave a good agreement for fluid pore occupancy between the simulation and the experiment. However, the constant contact angle assignment predicted 54% higher water effective permeability after waterflooding than that estimated for the experimental result, whereas the non-uniform contact angle assignment gave less than 1% relative error. This means that to correctly predict fluid conductivity in mixed-wet rocks, a spatially heterogeneous wettability state needs to be taken into account. The novelty of this work is to provide a direct pore-scale comparison between experiments and simulations employing experimentally measured contact angles, and to demonstrate how to use measured contact angle data to improve the predictability of direct numerical simulation, highlighting the difference between the contact angle required for the simulation of dynamic displacement process and the contact angle measured at equilibrium after waterflooding.

25 September 2019 in Transport in Porous Media
Verified
Journal Article
Open access
PDF file
TATakashi Akai
Takashi Akai
AAAmer M. Alhammadi
Amer M. Alhammadi
MBMartin J. Blunt
Martin J. Blunt
BBBranko Bijeljic
Branko Bijeljic
We demonstrate how to use numerical simulation models directly on micro-CT images to understand the impact of several enhanced oil recovery (EOR) methods on microscopic displacement efficiency. To describe the physics with high-fidelity, we calibrate the model to match a water-flooding experiment conducted on the same rock sample (Akai et al. in Transp Porous Media 127(2):393–414, 2019. 10.1007/s11242-018-1198-8). First we show comparisons of water-flooding processes between the experiment and simulation, focusing on the characteristics of remaining oil after water-flooding in a mixed-wet state. In both the experiment and simulation, oil is mainly present as thin oil layers confined to pore walls. Then, taking this calibrated simulation model as a base case, we examine the application of three EOR processes: low salinity water-flooding, surfactant flooding and polymer flooding. In low salinity water-flooding, the increase in oil recovery was caused by displacement of oil from the centers of pores without leaving oil layers behind. Surfactant flooding gave the best improvement in the recovery factor of 16% by reducing the amount of oil trapped by capillary forces. Polymer flooding indicated improvement in microscopic sweep efficiency at a higher capillary number, while it did not show an improvement at a low capillary number. Overall, this work quantifies the impact of different EOR processes on local displacement efficiency and establishes a workflow based on combining experiment and modeling to design optimal recovery processes.

21 October 2018 in Journal of Visualized Experiments
Verified
Journal Article
Open access
PDF file
AAAmer M. Alhammadi
Amer M. Alhammadi
AAAhmed AlRatrout
Ahmed AlRatrout
BBBranko Bijeljic
Branko Bijeljic
MBMartin J. Blunt
Martin J. Blunt
In situ wettability measurements in hydrocarbon reservoir rocks have only been possible recently. The purpose of this work is to present a protocol to characterize the complex wetting conditions of hydrocarbon reservoir rock using pore-scale three-dimensional X-ray imaging at subsurface conditions. In this work, heterogeneous carbonate reservoir rocks, extracted from a very large producing oil field, have been used to demonstrate the protocol. The rocks are saturated with brine and oil and aged over three weeks at subsurface conditions to replicate the wettability conditions that typically exist in hydrocarbon reservoirs (known as mixed-wettability). After the brine injection, high-resolution three-dimensional images (2 µm/voxel) are acquired and then processed and segmented. To calculate the distribution of the contact angle, which defines the wettability, the following steps are performed. First, fluid-fluid and fluid-rock surfaces are meshed. The surfaces are smoothed to remove voxel artefacts, and in situ contact angles are measured at the three-phase contact line throughout the whole image. The main advantage of this method is its ability to characterize in situ wettability accounting for pore-scale rock properties, such as rock surface roughness, rock chemical composition, and pore size. The in situ wettability is determined rapidly at hundreds of thousands of points. The method is limited by the segmentation accuracy and X-ray image resolution. This protocol could be used to characterize the wettability of other complex rocks saturated with different fluids and at different conditions for a variety of applications. For example, it could help in determining the optimal wettability that could yield an extra oil recovery (i.e., designing brine salinity accordingly to obtain higher oil recovery) and to find the most efficient wetting conditions to trap more CO2 in subsurface formations.

13 November 2017
Verified
Conference Paper
Closed access
PDF file
AAAmer M. Alhammadi
Amer M. Alhammadi
AAAhmed AlRatrout
Ahmed AlRatrout
BBBranko Bijeljic
Branko Bijeljic
MBMartin J. Blunt
Martin J. Blunt
More than a trillion barrels of oil may be extracted from carbonate reservoirs in the Middle East. Oil recovery is known to be controlled by wettability (distribution of contact angles) that determines the pore-scale fluid configuration. However, these contact angles have not hitherto been measured in situ at reservoir conditions for reservoir rock that is saturated with formation brine and crude oil. We use high resolution X-ray imaging of a sample from a producing oil field to demonstrate that contact angles over a wide range are seen both above and below 90°. More than a million points of contact angle were measured after three pore volumes of formation brine flooding. The injected brine invades the center of the pores as a non-wetting phase leaving oil trapped in small pores and corners in connected layers. Pores that were filled with initial formation brine remained water-wet. On the other hand, surfaces that were in direct contact with crude oil during aging were altered to oil-wet. However, water-wet surfaces were also measured in pores that were filled with crude oil which suggests that water layers in small pores, crevices, and within rock surface roughness, which might be connected to brine in micro-porosity, could prevent the contact between surface active polar compounds in the crude oil and the rock surfaces preventing strong wettability change. The reservoir rock became mixed-wet with a mean contact angle of 106° ± 20° obtained from 1.36 million in situ contact angle values measured using an automated algorithm (AlRatrout et al., 2017) applied on segmented three-dimensional X-ray image. The three-dimensional images were acquired using a high resolution X-ray micro-tomography scanner. The wetting condition resulted in a large volume of oil (50.6%) being trapped with a distinctive morphology as rough sheet-like layers.

12 November 2018
Verified
Conference Paper
Closed access
PDF file
ASAlessio Scanziani
Alessio Scanziani
AAAmer Alhammadi
Amer Alhammadi
BBBranko Bijeljic
Branko Bijeljic
MBMartin J. Blunt
Martin J. Blunt
A novel method is presented to characterise in situ three-phase flow, including wettability, pore occupancy and displacement mechanisms, at the pore scale. We used X-ray microtomography to obtain 3D images of a carbonate reservoir rock saturated with crude oil and formation brine at subsurface conditions. The sample had been aged with crude oil from the same reservoir to replicate the sunsurface wetting conditions. The pore occupancy analysis shows that brine is non-wetting to oil and gas is non-wetting to brine with a wettability order of oil-brine-gas from the most to the least wetting fluid. The waterflood recovery after 1 pore volume injected was only 14%, but this increased to 48% after further gas injection. New multiple displacement mechanisms were observed, with gas displacing brine, which in turn displaces oil. The results from this work can be used to improve the prediction accuracy of the three-phase network models and helps in the design of gas injection processes.