Most acoustic imaging methods assume the presence of point sound sources and, hence, may fail to correctly estimate the sound emissions of distributed sound sources, such as trailing-edge noise. In this contribution, three integration techniques are suggested to overcome this issue based on models considering a single point source, a line source, and several line sources, respectively. Two simulated benchmark cases featuring distributed sound sources are employed to compare the performance of these integration techniques with respect to other well-known acoustic imaging methods. The considered integration methods provide the best performance in retrieving the source levels and require short computation times. In addition, the negative effects of the presence of unwanted noise sources, such as corner sources in wind-tunnel measurements, can be eliminated. A sensitivity analysis shows that the integration technique based on a line source is robust with respect to the choice of the integration area (shape, position, and mesh fineness). This technique is applied to a trailing-edge-noise experiment in an open-jet wind tunnel featuring a NACA 0018 airfoil. The location and far-field noise emissions of the trailing-edge line source were calculated.

The recently introduced high-resolution (HR)-CLEAN-SC algorithm for acoustic imaging provides ‘super-resolution’, i.e. the ability to discern sound sources located closer than the Rayleigh resolution limit. This is achieved by allowing the source markers to be relocated from the actual source locations within a certain constraint to avoid the combined influence of the other sound sources. The freedom to relocate the source markers to increase the performance of the algorithm depends on the maximum sidelobe level of the acoustic array used. This paper presents an ‘enhanced’ version of the HR-CLEAN-SC algorithm which benefits from low maximum sidelobe level array design. The source marker constraint μ is adapted to the maximum sidelobe level at each frequency. Application to up to four synthetic sound sources shows that the sources can be resolved at half the frequency associated with the Rayleigh resolution limit, when an acoustic array optimized for low maximum sidelobe level is used in combination with Enhanced HR-CLEAN-SC. This improves source discrimination compared to when the HR-CLEAN-SC algorithm is used with a benchmark acoustic array design. The results are confirmed by experimental validation in which up to four loudspeakers and the same array configurations as in the synthesized data case are used.

Studies on porous trailing edges, manufactured with open-cell Ni-Cr-Al foams with sub-millimeter pore sizes, have shown encouraging results for the mitigation of turbulent boundary-layer trailing-edge noise. However, the achieved noise mitigation is typically dependent upon the pore geometry, which is fixed after manufacturing. In this study, a step to control the aeroacoustics effect of such porous trailing edges is taken, by applying a polymeric coating onto the internal foam structure. Using this method, the internal topology of the foam is maintained, but its permeability is significantly affected. This study opens a new possibility of aeroacoustic control, since the polymeric coatings are temperature responsive, and their thickness can be controlled inside the foam. Porous metallic foams with pore sizes of 580, 800, and 1200 μm are (internally) spray-coated with an elastomeric coating. The uncoated and coated foams are characterized in terms of reduced porosity, average coating thickness and air-flow resistance. Subsequently, the coated and uncoated foams are employed to construct tapered inserts installed at the trailing edge of an NACA 0018 airfoil. The noise mitigation performances of the coated metal foams are compared to those of uncoated metal foams with either similar pore size or permeability value, and both are compared to the solid trailing edge reference case. Results show that that the permeability of the foam can be easily altered by the application of an internal coating on the metallic foams. The noise reduction characteristics of the coated foams are similar to equivalent ones with metallic materials, provided that the coating material is rigid enough not to plastically deform under flow conditions.

This study focuses upon a new permeable topology design concept as an alternative to porous metal foams, for turbulent boundary layer trailing-edge (TBL-TE) noise attenuation. The present permeable topology has unconventional characteristics with respect to the metal foams: a combination of low flow resistivity r and high form drag coefficient C. The unconventional characteristics are realized by a Kevlar-covered 3D-printed perforated structure. An experimental study featuring a NACA 0018 airfoil model with a Kevlar-covered 3D-printed TE insert at chord-based Reynolds numbers up to $\text{4}.\text{6}\times {\text{10}}^{\text{5}}$ is carried out. The airfoil with this TE insert gives a broadband TBL-TE noise reduction up to approximately 5 dB, compared to a solid TE. This reduction varies only slightly with airfoil loading (lower than 1 dB variation), in contrast to the porous metal foams (up to 3 dB variation). When comparing the variation of noise attenuation given by all the permeable materials considered, the variation is found to decrease with the increasing C. This is because C specifies the permeable material's ability to withstand the increasing pressure difference, which causes cross flow that might interfere with the noise attenuation mechanism. Additionally, the drag coefficients as well as the roughness noise of the airfoil equipped with the present TE insert are also significantly lower than those of the metal-foam TE, and are mostly negligible compared to the fully solid airfoil. Based on the findings, design guidelines for permeable TE are proposed: the permeable material shall have a combination of a low flow resistivity and a high form drag coefficient as well as a negligible surface roughness.

Experimental results on trailing-edge (TE) noise from a NACA [ ] airfoil are presented for a chord-based Reynolds number [ ] range between [ ] and [ ]. Far-field TE noise from the baseline airfoil with a straight TE and TE serrations is measured with varying [ ], angle of attack, and serration shape and flap angle. Additionally, aerodynamic coefficients and boundary-layer parameters at the TE are also reported. To cover such a broad [ ] range, two NACA [ ] airfoil models were tested in two different wind tunnels. The measurements include the emitted noise with natural and forced transition locations. For the straight TE, the forced transition location results in up to 5 dB increase of the far-field TE noise level, compared to the natural one. Scaling of the far-field noise spectra from the baseline TE shows that the Strouhal numbers [ ] at which the peak noise level is measured reduce as [ ] increases. TE noise spectra for the cases with the TE serrations are found to be dependent on the airfoil lift and [ ]. The present data are to be included in the framework of the Benchmark Problems for Airframe Noise Computations category I and are publicly available in a repository with the following digital object identifier (DOI): https://doi.org/10.4121/20940646 .

This study covers three aspects of acoustic localisation of drones using a microphone array. First, it assesses a grid-free approach, using differential evolution, to estimate the three-dimensional position of a drone. It is found that this is indeed possible for the drone in the near-field. For larger distances, it still provides the angular position of the drone. Second, the study emphasizes the essence of localisation over small frequency bands with the bands jointly spanning a large frequency range to reveal the presence of multiple sound sources and maximise the drone localisation range. Third, it addresses the localisation ranges for six different drones.