A space curved surface shape reconstruction algorithm is proposed for shape perception and reconstruction of flexible plate structure. First, biorthogonal strain data measured by optimal distributed Fiber Bragg grating sensor network are converted to discrete curvature data. Second, interpolation is done to achieve curvature continuity for structural deformation. Third, moving coordinate systems are established in two orthogonal directions of the orthogonal curved network on the plate surface. Then, all nodal coordinates are computed using the given boundary conditions and nodal curvature. Coordinate transformation is done for two orthogonal coordinates according to the coupling relationship. Finally, a square flexible smart Fiber Bragg grating plate is constructed by implanting fiber grating sensor network, and a visualization experimental platform is constructed. Experimental analysis and verification were done. The experimental results show that the proposed shape reconstruction algorithm has good reconstruction performance for pure bending deformation, torsional deformation, and low-frequency dynamic vibration shape.
The engine blade is one of the important parts of the aero engine, vibration can lead to engine blade off or fracture. Active Vibration Control (AVC) has a higher flexibility is increasingly used to suppress the vibration of the blade. The filtered-x least mean square (FxLMS) algorithm is an adaptive algorithm commonly used in active vibration control, but its fixed step size has a contradiction between convergence speed and steady-state error. A new variable-step-size FxLMS (VSSFxLMS) algorithm based on hyperbolic secant function was proposed, and the sech function ensures the control signal is bounded. In the early stage, a larger step size enables the error to decrease rapidly. The step size decreases as the error decreases, and a smaller step size ensures a smaller steady-state error. Firstly, this paper summarizes three VSSFxLMS algorithms and proposes an improved algorithm; Secondly, it compares and analyses the mentioned algorithms; Then, a joint simulation platform using ADAMS and Simulink is built to verify the effectiveness of the proposed algorithms; Finally, an experimental platform was built to complete the blade vibration active control experiments using several VSSFxLMS algorithms, and the results of the experiment verify the better vibration suppression effect of the proposed algorithm.
14 November 2018 in Journal of Low Frequency Noise, Vibration and Active Control
The step size of least mean square (LMS) algorithm is significant for its performance. To be specific, small step size can get small excess mean square error but results in slow convergence. However, large step size may cause instability. Many variable step size least mean square (VSSLMS) algorithms have been developed to enhance the control performance. In this paper, a new VSSLMS was proposed based on Kwong’s algorithm to evaluate the robustness. The approximate analysis of dynamic and steady-state performance of this developed VSSLMS algorithm was given. An active vibration control system of piezoelectric cantilever beam was established to verify the performance of the VSSLMS algorithms. By comparing with the current VSSLMS algorithms, the proposed method has better performance in active vibration control applications.
12 January 2022 in Transactions of the Institute of Measurement and Control
A discrete-time-modified Bouc–Wen model is proposed to describe the non-symmetrical and rate-dependent hysteresis of piezoelectric actuators for micro-vibration control applications. The modified model combines a non-symmetrical Bouc–Wen model and a frequency-dependent dynamic module. A series of experiments are conducted to characterize the rate-dependent hysteresis of piezoelectric stack actuators under sinusoidal excitations at a range of 1 to 20 Hz. The experimental results verify the validity of the modified model. The modified Bouc–Wen model increases the complexity of Bouc–Wen hysteresis nonlinear differential equation, which brings difficulties to parameter identification. To identify the parameters of Bouc–Wen model, an improved hybrid differential evolution and Jaya (DE-Jaya) algorithm is introduced with a hybrid mutant operator and Jaya operator that tried to balance between convergence speed and solution accuracy. The improved algorithm is tested on benchmark functions and compared with other optimizations to prove its effectiveness. The comparison results show that hybrid DE-Jaya algorithm has better performance in convergence speed and solution accuracy. The identified discrete-time-modified Bouc–Wen model is used as the secondary path in a filtered-x variable step-size affine projection algorithm (FXVSSAPA), and experimental verifications are done on a micro-vibration control platform. The experimental results show that the FXVSSAPA algorithm can converge to the steady-state error faster and verify the effectiveness of the proposed discrete-time-modified Bouc–Wen model.