The structural application of synthetic fibre reinforced concrete (FRC) has become widespread in the construction industry in order to satisfy the requirement of the earthquake resistant structures. Research conducted so far are focused on the structural behaviour of RC column externally confined with FRP composites, while studies are needed to address the behaviour of FRP strengthened RC column fabricated using fibre reinforced concrete. With the intention that the experimental investigation was carried out to evaluate the feasibility use of CFRP composite strips in strengthening of RC column made with fibre reinforced concrete. Circular synthetic Polypropylene fibre was used in the rate of 0.50% in the volume of concrete. CFRP strips having a width of 50 mm were used to confine the column and the experimental parameters were effective spacing between the CFRP strips (20 mm and 30 mm) and the number of CFRP layers (one, two and three). The externally bonded CFRP strips counteract the lateral expansion of the concrete significantly by providing restraining effect and thus effect enhanced the stiffness of the column. The column strengthened with CFRP strips showed a maximum of 198.87% and 91.75% enhancement in axial deformation control and ultimate strength, respectively, compared to that of reference column. From the test results obtained, it is suggested that CFRP strips with the spacing of 20 mm and 30 mm can be used in strengthening of RC column made with FRC; however the column confined with 30 mm spacing provides an economical advantage compared to that of 20 mm spacing.
This paper presents the findings of investigation, which was instigated to assess the effects of fibre aspect-ratio on the fresh and mechanical properties of SCC. The investigational parameters were aspect-ratio of the fibre and fibre addition rate. Two different aspect-ratios (64 and 73) of steel fibre were used and the fibre addition rate was between 0.2% and 1.0% with the increment of 0.2% and the fibres were added to the SCC in volume fraction. A series of tests were performed to determine the impact of fibre aspect-ratio and fibre inclusion rate on the engineering/mechanical properties of SCC. The presence of steel fibre in the SCC lessened the workability; furthermore, the upsurge in the inclusion rate of steel fibre abridged the workability further. The inclusion of fibre boosted the compressive strength of the SCC moderately, and conversely, an overwhelming increase in flexural and tensile strength was observed. The rise in the fibre aspect-ratio caused a 2.53% augmentation in the compressive strength of the SCC. Nevertheless, more than 11% improvement in tensile strength was observed, because of the bridging/anchorage established by the fibre. From the obtained results, it can be inferred that the impact of fibre aspect-ratio on the compressive strength of the SCC is not substantial; however, the tensile strength properties of the SCC can be enhanced moderately by increasing the fibre aspect-ratio.
Slope protection and erosion management are severely hampered by the rapid infrastructure development in mountainous valleys, especially during the monsoon season. While conventional approaches like vegetation, porous concrete, and inorganic procedures have been used, stronger and more ecologically friendly alternatives are still needed. A new kind of concrete called vegetation concrete (VC) allows roots to grow through the concrete frame by combining plant integration with porous concrete. This creative method might be used for environmentally friendly building and planting. The alkalinity of VC significantly impacts its planting capabilities and soil nutrient levels, making it crucial to reduce VC alkalinity. In this study, silica fume (SF) and fly ash (FA) were combined to create low-alkaline VC. The effects of SF and FA on VC’s alkalinity, porosity, compressive strength, and planting characteristics were examined. The study also investigated VC’s influence on soil fertility and its impact on soil nutrients. Test results revealed that SF and FA reduced the pH of the VC by reducing calcium hydroxide (CH) crystals. While SF had a lower basicity coefficient ( M ) than FA, it had a more significant effect on lowering VC alkalinity. The compressive strength decreased with FA but increased with SF, despite SF having a smaller cement component in VC–SF mixes. This suggests that blending VC with SF and FA is feasible, with the SF dosage exceeding the FA dosage for reduced alkalinity and increased strength. Lowering VC alkalinity through SF and FA increased soil nutrients, including hydrolyzable nitrogen (AH-N), extractable phosphorus (P), and potassium (K). It also improved planting properties like root development, stem height, and leaf relative water content. Using VC for soil stabilization did not reduce soil fertility but instead increased the available phosphorus and alkali-hydrolyzable nitrogen in the soil by 32.81 and 52.92%, respectively. The findings of this study open up new avenues for investigation into this technology and have important ramifications for the use of VC technology, particularly in Indian contexts.
23 February 2014 in Advances in Materials Science and Engineering
The feasibility study on carbon fibre reinforced polymer (CFRP) fabrics in axial strengthening of hollow square sections (HSS) was investigated in this paper. CFRP was used as strips form with other parameters such as the number of layers and spacing of strips. Experimental results revealed that the external bonding of normal modulus CFRP strips significantly enhanced the load carrying capacity and stiffness of the hollow sections and also reduced the axial shortening of columns by providing external confinement against the elastic deformation. The increase in the CFRP strips thickness effectively delayed the local buckling of the above members and led to the inward buckling rather than outward one. Finally, three-dimensional nonlinear finite element modeling of CFRP strengthened hollow square sectionswas created by using ANSYS 12.0 to validate the results and the numerical results such as failure modes and load deformation behaviour fairly agreed with the experimental results.
4 September 2013 in Arabian Journal for Science and Engineering