This brief presents a nano-ampere CMOS current reference (CCR) for low power application with a wide temperature range from -40 ∘C to 120 ∘C. The current reference is generated by the division of a temperature-independent voltage and resistance in a simple way. The low temperature-independent voltage is generated based on the threshold voltage difference between two same-type NMOS transistors with different channel lengths working in the subthreshold region, while the temperature-independent resistance is made up by two poly resistors, whose temperature coefficients are opposite. By designing a low voltage to allow for a small resistance, the CCR circuit takes a small chip area while generating nano-ampere current. The proposed CCR circuit was implemented in a standard 0.18-μm CMOS process and its active area is 0.054 mm2. Among the measured 10 samples, the average output current is 11.6 nA and the average temperature coefficient is 169 ppm/∘C.
8 May 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents a CMOS wideband passive balun low noise amplifier (LNA) based on magnetically coupled resonator (MCR) matching network. The theoretical analysis, expression derivation and simulation verification of the impedance rise with frequency of MCR matching network is presented for the first time. The proposed wideband LNA was fabricated in 22-nm CMOS technology, which achieves a maximum power gain of 15.7 dB, noise figure (NF) of 1.46-1.96 dB. The 3-dB bandwidth ranges from 2.1-5.2 GHz. The minimum power input at 1dB compression point (IP1dB) is -15.2 dBm. The LNA core area is 0.38 mm2 and dissipates a total power of 16 mW from 1 V power supply.
25 October 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a low power injection-locked oscillator (ILO)-type clock and data recovery (CDR) in 40 nm CMOS. An efficient “phase reset” scheme is proposed to periodically realign the clock phase to the rising edge of data. The frequency information is extracted by comparing the rising edge of the data and the clock after aligning the phase using a bang-bang phase detector (BBPD). Additionally, a low power injection-locked two-stage ring digitally controlled oscillator (ILDCO) is employed to provide four-phase quadrature clock and significantly reduce the power consumption. Based on the proposed architecture, the fabricated CDR consumes only 5.8 mW from a 0.9 V supply, while being able to extract the clock signal from 6.15 to 10.9 Gb/s input data with a measured jitter tolerance (JTOL) of 0.15 UIpp at the highest frequency, indicating that the CDR meets the OC-192 mask. Furthermore, the proposed CDR demonstrates a substantial improvement in the power efficiency of 0.58 pJ/bit.
1 January 2018 in AEU - International Journal of Electronics and Communications
A broadband low‐noise amplifier (LNA) is proposed. The active
g
m ‐boosting technique is utilised to reduce the common‐gate (CG) LNA noise figure and improve gain. An implemented prototype using 0.13 μm CMOS technology is evaluated using on‐wafer probing. S11 and S22 are below − 10 dB across 0.1–5 GHz. Measurements show a power gain of 18.3 dB with a − 3 dB bandwidth from 100 MHz to 2.1 GHz and an IIP3 of − 7 dBm at 2 GHz. The measured noise figure is better than 2.5 dB below 2.1 GHz, better than 4.5 dB below 5 GHz and at 500 MHz it obtains its minimum value 1.8 dB. The LNA consumes 14 mW from 1.5 V supply and occupies an area of 0.04 mm 2 .
18 August 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article describes a wideband low-noise frequency synthesizer implemented in 0.13-μm SiGe BiCMOS process for 5G millimeter-wave applications. To extend the frequency range while reducing the phase noise, a fundamental voltage-controlled oscillator (VCO) array including four Colpitts VCO cores with switchable bias circuits is adopted in the proposed frequency synthesizer. A ring-oscillator-based injection locked frequency divider is utilized as the wideband divide-by-2 prescaler, and its bandwidth is optimized based on a new injection-locked behavior model. This fabricated frequency synthesizer can be locked in a range from 23 to 36.8 GHz (46.2%) by a 100-MHz step. It achieves a phase noise of -94.7 dBc/Hz at the 1-MHz offset and an output power of -3.5 dBm measured at 36.8 GHz. The chip consumes 360.6 mW from 3.3 and 1.8 V supplies and has an area of 2.7 x 3.1 mm².