18 August 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article describes a wideband low-noise frequency synthesizer implemented in 0.13-μm SiGe BiCMOS process for 5G millimeter-wave applications. To extend the frequency range while reducing the phase noise, a fundamental voltage-controlled oscillator (VCO) array including four Colpitts VCO cores with switchable bias circuits is adopted in the proposed frequency synthesizer. A ring-oscillator-based injection locked frequency divider is utilized as the wideband divide-by-2 prescaler, and its bandwidth is optimized based on a new injection-locked behavior model. This fabricated frequency synthesizer can be locked in a range from 23 to 36.8 GHz (46.2%) by a 100-MHz step. It achieves a phase noise of -94.7 dBc/Hz at the 1-MHz offset and an output power of -3.5 dBm measured at 36.8 GHz. The chip consumes 360.6 mW from 3.3 and 1.8 V supplies and has an area of 2.7 x 3.1 mm².
31 October 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper describes a Ku-band passive time-varying phase shifter (TVPS). The time variable is introduced into the conventional vector-sum phase shifter (VSPS) architecture, and the time-varying vector-sum method is proposed for the first time to realize continuous phase shifting. The proof-of-concept passive TVPS consisting of a quadrature coupler, two 0/180∘ bi-phase modulators and an output combiner is implemented in 0.13-μm CMOS technology with a core area of 2.2×0.8 mm2, and a fieldprogrammable gate array (FPGA) is used to provide gain-control timing sequences with the modulation frequency of 100 kHz for its four control bits. The timing sequences are optimized to eliminate unwanted sidebands, and the measured sideband suppression ratio (SSR) is -17.2 dBc. For both forward and backward phase shifting modes, measured results show that the proposed TVPS can achieve the phase resolution of 10-bits, RMS phase error of 0.2 0.5∘, RMS gain error of less than 0.2 dB over the 12 18 GHz frequency band.
14 December 2022 in Microelectronics Journal
1 December 2023 in Electromagnetic Science
In this paper, three switchable electromagnetic absorbers/reflectors using back-loaded active radio frequency circuits are presented. In the first design, the incident waves are received by an antenna array, transmitted to the back-loaded active circuits and then reflected into the free space when the PIN diode in series in the circuit is off. When the diode is on, the incident waves can be absorbed by a matching load. In the second design, the phase of the reflected waves in the unit cell can be manipulated by adjusting the length of the microstrip lines, allowing the reflection polarization to be tuned. In the third design, by integrating RF switching chips into the back-loaded circuits, a switchable absorber/reflector with a switching polarization state is presented. The first design is fabricated and measured. The profile of the switchable absorber/reflector is approximately $0.14\lambda_{l}$ . A total of 2 PIN diodes are used per unit cell for both TE and TM polarizations. By using active circuits, flat in-band reflection performance and stable absorption performance can be achieved in the frequency band of 7 to 18.5 GHz (FBW of 90%) for normal incidence, and an angular stability of 45° for TE and TM polarizations is realized.
17 September 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
A wideband active single-sideband time modulator (STM) is proposed in this paper, which achieves high-resolution frequency-independent phase shifting performance through high-precision time delay, eliminating the need for calibrations. The analysis starts with $N$ -step time modulation sequences for the active STM, followed by discussions on enhancing the sideband suppression ratio (SSR) and the effects of quadrature mismatch on SSR. The proposed active STM is based on a periodically controlled active vector modulator with regularly scalable gate-widths, and its timing sequences for control bits feature identical duty cycles and modulation frequency ( $f_{\mathrm{P}})$ . For verification, a wideband active STM is implemented using 0.13- $\mu $ m CMOS technology, which is composed of an input balun and quadrature generator, a periodically controlled 4-bit active vector modulator and a variable-gain stage. Measurement results indicate root mean square (RMS) phase and gain errors ranging from 0.1 to 0.4 $^{\circ}$ and less than 0.2 dB respectively, within a 3-dB frequency range of 13.0 to 20.6 GHz at the maximum gain state. The active STM provides a peak gain of $-$ 0.1 dB, an equivalent 10-bit phase control across a 360 $^{\circ}$ range, and a 3-bit gain control spanning 21.0 dB. The measured SSR is below $-$ 23.3 dBc, and the instantaneous bandwidth is expanded to 16 $f_{\mathrm{P}}$ . Additionally, the input 1-dB compression point (IP $_{\mathrm{1dB}})$ ranges from 6.1 to 9.3 dBm. The chip occupies a 2.4 mm $^{2}$ area and consumes 58.8 mW from a 1.2 V supply voltage.
4 November 2025 in IEEE Microwave and Wireless Technology Letters
This letter presents a novel design method for wideband low-noise amplifiers (LNAs), which decouples the realization procedure of input noise matching, input impedance matching, and gain flatness. The input matching network is designed to realize wideband noise matching. Then, the degeneration inductor and T-type interstage matching network with magnetic coupling are employed to meet the required range of the interstage impedance mismatch level to achieve wide input impedance bandwidth. The gain bandwidth is enhanced by designing the impedance mismatch related to output matching network, without affecting the input matching. For demonstration, a three-stage E-/W-band LNA has been implemented using a 0.13- $\mu $ m SiGe BiCMOS technology. The LNA achieves a peak gain of 24.1 dB with a 3-dB gain bandwidth of 53 GHz, less than −10-dB $\vert S_{11} \vert $ bandwidth of 50 GHz, and a low noise figure (NF) ranging from 3.8 to 6.9 dB across the W-band, while consuming power of 23 mW.