Composites based on epoxy/graphene oxide (GO) and epoxy/reduced graphene oxide (rGO) were investigated for thermal-mechanical performance focusing on the effects of the chemical groups present on nanoadditive-enhanced surfaces. GO and rGO obtained in the present study have been characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and X-ray powder diffraction (XRD) demonstrating that materials with different oxidation degrees have been obtained. Thereafter, GO/epoxy and rGO/epoxy nanocomposites were successfully prepared and thoroughly characterized by dynamic mechanical thermal analysis (DMTA) and transmission electron microscopy (TEM). A significant increase in the glass transition temperature was found in comparison with the neat epoxy. The presence of functional groups on the graphene surface leads to chemical interactions between these functional groups on GO and rGO surfaces with the epoxy, contributing to the possible formation of covalent bonds between GO and rGO with the matrix. The presence of oxidation groups on GO also contributes to an improved exfoliation, intercalation, and distribution of the GO sheets in the composites with respect to the rGO based composites.

In the last decades, the demand for electronics and, therefore, electronic waste, has increased. To reduce this electronic waste and the impact of this sector on the environment, it is necessary to develop biodegradable systems using naturally produced materials with low impact on the environment or systems that can degrade in a certain period. One way to manufacture these types of systems is by using printed electronics because the inks and the substrates used are sustainable. Printed electronics involve different methods of deposition, such as screen printing or inkjet printing. Depending on the method of deposition selected, the developed inks should have different properties, such as viscosity or solid content. To produce sustainable inks, it is necessary to ensure that most of the materials used in the formulation are biobased, biodegradable, or not considered critical raw materials. In this review, different inks for inkjet printing or screen printing that are considered sustainable, and the materials that can be used to formulate them, are collected. Printed electronics need inks with different functionalities, which can be mainly classified into three groups: conductive, dielectric, or piezoelectric inks. Materials need to be selected depending on the ink’s final purpose. For example, functional materials such as carbon or biobased silver should be used to secure the conductivity of an ink, a material with dielectric properties could be used to develop a dielectric ink, or materials that present piezoelectric properties could be mixed with different binders to develop a piezoelectric ink. A good combination of all the components selected must be achieved to ensure the proper features of each ink.

A super-hydrophobic surface at a high temperature (400 °C) using the sol-gel method with tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) as precursors has been obtained. The effects of the coatings’ ages, deposited times and thicknesses on the hydrophobicity of the silica coatings have been analysed. The morphology, chemical composition, thermal degradation and hydrophobicity of the resulting surfaces have been studied by scanning electron microscopy (SEM), Fourier transfer infrared spectrometer (FT-IR), Thermogravimetry (TGA) and water contact angle (WCA) measurement. The results show that an average water contact angle of 149° after been cured at 400 °C for a coating aged for 5 days, and four deposition cycles using a dipping rate of 1000 mm/min was achieved.

This work has been focused on the one-step fabrication by electrospinning of polyamide 6 (PA6) nanofibre membranes modified with titanium dioxide nanoparticles (TiO₂), where these TiO₂ nanoparticles aggregates could induce a photocatalytic activity. The main potential application of these membranes could be the purification of contaminated water. Thus, it is important to analyse the contaminant degradation capability since in these membranes this is based on their photocatalytic activity. In this work, the effect of the photocatalysis has been studied both on the degradation of an organic model contaminant and on the removal of Escherichia coli and other coliform bacteria. As a result, it was observed that these membranes present excellent photocatalytic activity when they are irradiated under UV light, allowing a 70% reduction of an organic model pollutant after 240 min. In addition, these membranes successfully removed Escherichia coli and other coliform bacteria in artificially inoculated water after 24 h of contact with them. Moreover, the stand-alone structure of the membranes allowed for the reusing of the immobilized catalyst. The experimental evidence indicated that developed nanofibre membranes are a fast and efficient solution for polluted water decontamination based on photocatalysis. Their use could contribute to guarantee a fresh water level and quality, mitigating the water scarcity problem worldwide.

The reflector is the first key component in the energy conversion process of concentrating solar technologies as any solar radiation that is not reflected by the mirror in the direction of the receiver is lost to the system. Due to the outdoor exposure, solar reflectors are subjected to constant soiling deposition (including dust, sand and/or dirtiness), which severely decreases the output power of the solar concentrating collectors, as it reduces the amount of radiation that can be reflected towards the receiver (associated to the absorption and scattering effects of light). Most of the Concentrating Solar Power (CSP) plants are installed in regions of high Direct Normal Irradiance (DNI) with arid and semi-arid climate, involving the existence of an important amount of dust and sand in the ambient. Collector cleanliness represents one of the most costly expenses of the solar-plant operation and maintenance (O&M). Consequently, minimizing this cost is an important issue for the solar-plant economic feasibility. Anti-soiling coatings deposited on the surface of silvered-glass reflectors are a powerful tool that can help in repelling all sort of dust, sand and particles. This technological solution presents the following benefits: (i) the maintenance cost is driven down by reducing washing times, (ii) the water consumption is drastically diminished and (iii) the efficiency is increased since the average reflectance of the solar field remains higher. This work presents the behavior of a new anti-soiling coating with improved durability and high efficiency.

Delamination and brittle matrix fracture have long since been the biggest problems in fibre-reinforced composites. Recently, the incorporation of electrospun nanofibre veils has been shown to be an effective method for improving the mechanical properties of these composites, without causing process problems and negatively affecting other mechanical properties. Thus, these nanofibres have the potential to be used as thickness-reinforcing materials in composites. This paper investigates the effect of incorporating standalone electrospun nanofibre veils made of two different types of polyamide 6 (PA6) on the mechanical properties of carbon fibre/epoxy composites. The influence of positioning the electrospun veils at different interlaminar positions of the laminate has also been investigated.