Gamma-ray spectrometry is a surveying technique that allows the calculation of the heat produced during radioactive decay of potassium, uranium, and thorium within rock. Radiogenic heat producing rocks are often targets for geothermal exploration and production. Hence, refinements in gamma-ray spectrometry surveying will allow better constraint of resources estimation and help to target drilling. Gamma-rays have long half-lengths compared to other radiation produced during radiogenic decay. This property allows the gamma-rays to penetrate far enough through media to be detected by airborne or ground based surveying. A recent example of ground-based surveying in Scotland shows the ability of gamma-ray spectrometry to quickly and efficiently categorize granite plutons as low or high heat producing. Some sedimentary rocks (e.g., black shales) also have high radiogenic heat production properties and could be future geothermal targets. Topographical, atmospheric and spatial distribution factors (among others) can complicate the collection of accurate gamma-ray data in the field. Quantifying and dealing with such inaccuracies represents an area for further improvement of these techniques for geothermal applications.
1 October 2019 in Science of The Total Environment
Deep geothermal energy is widely recognised as a source of low carbon heat. However, to date there have been no specific assessment of the carbon intensity of low-enthalpy deep geothermal; previous studies focussed on geothermal power or higher enthalpy heat. As such, there is no established method for assessing the CO2 emissions from implementing a deep geothermal heating scheme. Here we address these gaps. We perform a life cycle assessment of greenhouse gas emissions relating to a deep geothermal heat system to (i) calculate the carbon intensity of geothermal heat; (ii) identify key factors affecting these values; (iii) consider the carbon abated if geothermal heat substitutes conventional heating; and (iv) present information that future projects can apply to assess the carbon emissions reduction offered by geothermal heat development. Our work is informed by parameters from a feasibility study for a proposed geothermal heat system in Banchory, Scotland. The project planned a 2.5 MWth geothermal plant extracting heat from the Hill of Fare granite via two boreholes, one injection and one production. We find that the majority of the emissions are associated with site construction, and sensitive to site and materials specific factors, for example the depth of the drilled boreholes and type and quantities of steel and cement used to seal them, or soils disturbed for laying pipelines and constructing access roads. During operation the carbon intensity of the electricity grid used to power hydraulic pumps largely determines the carbon intensity of the produced heat. We calculate that the carbon intensity of the heat produced is 9.7-14.0 kg(CO2e) MWhth which is 4.9-7.3% of the emissions from heat from natural gas. These values are compatible with Scotland's plans for long term decarbonisation of heat in line with national emission reduction obligations and would likely be compatible with any country's decarbonisation goals.
9 January 2018 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
In 2015, the primary energy demand in the UK was 202.5 million tonnes of oil equivalent (mtoe = 848 EJ). Of this, about 58 mtoe (2.43 EJ) was used for space heating. Almost all of this heat was from burning fossil fuels either directly (50% of all gas used is for domestic purposes) or indirectly for power generation. Burning fossil fuels for heat released about 160 million tonnes of carbon dioxide in 2015. The UK must decarbonise heating for it to meet its commitments on emissions reduction. UK heat demand can be met from ultra-low-carbon, low enthalpy geothermal energy. Here we review the geothermal potential of the UK, comprising a combination of deep sedimentary basins, ancient warm granites and shallower flooded mines. A conservative calculation of the contained accessible heat in these resources is 200 EJ, about 100 years supply. Presently only one geothermal system is exploited in the UK. It has been supplying about 1.7MWT (heat) to Southampton by extracting water at a temperature of 76 ℃ from a depth of 1.7 km in the Wessex Basin. Like Southampton, most of the major population centres in the UK lie above or adjacent to major geothermal heat sources. The opportunity for using such heat within district heating schemes is considerable. The consequences of developing a substantial part of the UK’s geothermal resource are profound. The baseload heating that could be supplied from low enthalpy geothermal energy would cause a dramatic fall in the UK’s emissions of greenhouse gases, reduce the need for separate energy storage required by the intermittent renewables (wind and solar) and underpin a significant position of the nation’s energy security for the foreseeable future, so lessening the UK’s dependence on imported oil and gas. Investment in indigenous energy supplies would also mean retention of wealth in the UK.
1 May 2018 in International Journal of Coal Geology
Prior investigations concur that the granite plutons in Scotland which are most likely to prove favourable for geothermal exploration are the Ballater, Bennachie, Cairngorm and Mount Battock plutons, all of which have heat production values greater than 5 μW m −3 . This heat production arises from the significant concentrations of potassium, uranium and thorium in some granite plutons. A new field-based gamma-ray spectrometric survey targeted plutons that were poorly surveyed in the past or near areas of high heat demand. This survey identifies several other plutons (Ben Rhinnes, Cheviot, Hill of Fare, Lochnagar and Monadhliath) with heat production rates between 3 and 5 μW m −3 that could well have geothermal gradients sufficient for direct heat use rather than higher temperatures required for electricity generation. The Criffel and Cheviot plutons are examples of Scottish granites that have concentric compositional zonation and some zones have significantly higher (up to 20%) heat production rates than others in the same plutons. However, the relatively small surface areas of individual high heat-production zones mean that it is unlikely to be worthwhile specifically targeting them. Supplementary material: The full set of heat production data is available at https://doi.org/10.5525/gla.researchdata.302
This study examines the influences on fluid flow within a shale outcrop where the networks of two distinct paleoflow episodes have been recorded by calcite-filled veins and green alteration halos. Such direct visualization of flow networks is relatively rare and provides valuable information of fluid-flow behavior between core and seismic scale. Detailed field mapping, fracture data, and sedimentary logging were used over a 270 m2 (2910 ft2) area to characterize the paleo–fluid-flow networks in the shale. Distal remnants of turbidite flow deposits are present within the shale as very thin (1–10 mm [0.04–0.4 in.]) fine-grained sandstone bands. The shale is cut by a series of conjugate faults and an associated fracture network, all at a scale smaller than seismic detection thresholds. The flow episodes used fluid-flow networks consisting of subgroups of both the fractures and the thin turbidites. The first fluid-flow episode network was mainly comprised of thin turbidites and shear fractures, whereas the network of the second fluid-flow episode was primarily small joints (opening mode fractures) connecting the turbidites. The distribution of turbidite thicknesses follows a negative exponential trend. which reflects the distribution of thicker turbidites recorded in previous studies. Fracture density varies on either side of faults and is highest in an area between closely spaced faults. Better predictions of hydraulic properties of sedimentary-structural networks for resource evaluation can be informed from such outcrop subseismic scale characterization. These relationships between the subseismic features could be applied when populating discrete fracture networks models, for example, to investigate such sedimentary-structural flow networks in exploration settings.