Gregor Mori

Prof. Gregor Mori


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
ATAnton Trautmann
Anton Trautmann
GMGregor Mori
Gregor Mori
MOMarkus Oberndorfer
Markus Oberndorfer
SBStephan Bauer
Stephan Bauer
GMGregor Mori
Gregor Mori
CDChristoph Dittmann
Christoph Dittmann
To avoid failures due to hydrogen embrittlement, it is important to know the amount of hydrogen absorbed by certain steel grades under service conditions. When a critical hydrogen content is reached, the material properties begin to deteriorate. The hydrogen uptake and embrittlement of three different carbon steels (API 5CT L80 Type 1, P110 and 42CrMo4) was investigated in autoclave tests with hydrogen gas (H2) at elevated pressure and in ambient pressure tests with hydrogen sulfide (H2S). H2 gas with a pressure of up to 100 bar resulted in an overall low but still detectable hydrogen absorption, which did not cause any substantial hydrogen embrittlement in specimens under a constant load of 90% of the specified minimum yield strength (SMYS). The amount of hydrogen absorbed under conditions with H2S was approximately one order of magnitude larger than under conditions with H2 gas. The high hydrogen content led to failures of the 42CrMo4 and P110 specimens.

1 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
Krzysztof RokoszKrzysztof Rokosz
Krzysztof Rokosz
GSGrzegorz Solecki
Grzegorz Solecki
GMGregor Mori
Gregor Mori
RFRainer Fluch
Rainer Fluch
MKMarianne Kapp
Marianne Kapp
JLJouko Lahtinen
Jouko Lahtinen
In the present paper, the effect of different polishing methods (mechanical and electrochemical) on passive layer chemistry and the corrosion behavior of stainless steels is investigated. It was found that CrNiMo austenites have a substantially better corrosion behavior than CrMnN ones. The nickel is enriched underneath the passive layer, while manganese tends to be enriched in the passive layer. It was also noted that immersion of manganese into an electrolyte preferentially causes its dissolution. It was found that high amounts of chromium (27.4%), molybdenum (3.3%), nickel (29.4%), with the addition of manganese (2.8%) after mechanical grinding, generates a better corrosion resistance than after electrochemical polishing. This is most likely because of the introduction of phosphates and sulfates into its structure, which is known for steels with a high amount of manganese. For highly alloyed CrNiMo steels, which do not contain a high amount of manganese, the addition of phosphates and/or sulphates via the electropolishing process results in a decrease in pitting corrosion resistance, which is also observed for high manganese steels. Electropolished samples show detrimental corrosion properties when compared to mechanically polished samples. This is attributed to substantial amounts of sulfate and phosphate from the electropolishing electrolyte present in the surface of the passive layer.

19 December 2024 in Corrosion Science
Verified
Journal Article
Open access
AHAhmed Hamed
Ahmed Hamed
CPChristian Posch-Peperkorn
Christian Posch-Peperkorn
JMJuergen Maierhofer
Juergen Maierhofer
MBMonika Beschliesser
Monika Beschliesser
SFStefan Fink
Stefan Fink
GMGregor Mori
Gregor Mori

13 March 2023 in Corrosion Science
Verified
Journal Article
Open access
MTMathias Truschner
Mathias Truschner
RKRobin Kroll
Robin Kroll
MEMatthias Eichinger
Matthias Eichinger
AKAndreas Keplinger
Andreas Keplinger
DEDirk L. Engelberg
Dirk L. Engelberg
GMGregor Mori
Gregor Mori

12 July 2021 in Materials and Corrosion
Verified
Journal Article
Open access
PDF file
AGAnastasiia Galakhova
Anastasiia Galakhova
KPKarl Prattes
Karl Prattes
GMGregor Mori
Gregor Mori
Stress corrosion cracking test methods of corrosion‐resistant alloys are reviewed. The interest to write a review on this topic was drawn by demands for oil country tubular goods applicable in deep wells with high pressures, high temperatures, and the presence of H2S, where stress corrosion cracking is one of the most critical failure modes. All conventional methods for determining the stress corrosion cracking resistance of an alloy, mainly slow strain rate testing, constant load testing (tensile, 4‐PB), constant strain testing (U‐bend, C‐ring), and fracture mechanics (double cantilever beam sample) are covered. Considering the variety of testing solutions, the field of search is narrowed to hot (up to 250°C) aqueous chloride solutions with dissolved H2S and CO2gases under high pressure (up to 200 bar total pressure).

17 June 2024 in Corrosion Science
Verified
Journal Article
Open access
MEMatthias Eichinger
Matthias Eichinger
JPJohann Pengg
Johann Pengg
DZDino Zwittnig
Dino Zwittnig
GMGregor Mori
Gregor Mori