The electrical conductivity of brine‐saturated rock is predominantly dependent on the geometry and topology of the pore space. When a resistive second phase (e.g., air in the vadose zone and oil/gas in hydrocarbon reservoirs) displaces the brine, the geometry and topology of the pore space occupied by the electrically conductive phase are changed. We investigated the effect of these changes on the electrical conductivity of rock partially saturated with brine. We simulated drainage and imbibition as invasion and bond percolation processes, respectively, in pipe networks assumed to be perfectly water‐wet. The simulations included the formation of a water film in the pipes invaded by the nonwetting fluid. During simulated drainage/imbibition, we measured the changes in resistivity index as well as a number of relevant microstructural parameters describing the portion of the pore space saturated with water. Except Euler topological number, all quantities considered here showed a significant level of “universality,” i.e., insensitivity to the type of lattice used (simple cubic, body‐centered cubic, or face‐centered cubic). Hence, the coordination number of the pore network appears to be a more effective measure of connectivity than Euler number. In general, the simulated resistivity index did not obey Archie's simple power law. In log‐log scale, the resistivity index curves displayed a substantial downward or upward curvature depending on the presence or absence of a water film. Our network simulations compared relatively well with experimental data sets, which were obtained using experimental conditions and procedures consistent with the simulations. Finally, we verified that the connectivity/heterogeneity model proposed by Bernabé et al. (2011) could be extended to the partial brine saturation case when water films were not present.
10 April 2015 in Geophysical Journal International
In this paper, we modelled the electrical transport behaviour of bimodal carbonate rocks from a reservoir in China using dual-pore networks. One basic assumption, generally supported by experimental data and microstructure observations in the reservoir samples, was that the low porosity, monomodal rocks had the same properties and structure as the microporous matrix of the high porosity, bimodal samples. We assumed that the matrix was homogeneous and always interconnected but that the connectivity and the pore size distribution of macropore system was randomly variable. Both pore systems were supposed to act locally as ‘in parallel’ electrical conductors, an approach previously used by Bauer et al. Hence, the effect of matrix properties, macropore size distribution and connectivity on electrical properties of bimodal rocks could be modelled and investigated. We simulated electrical current through 3-D, simple cubic and body-centred cubic networks with different coordination numbers, different pipe radius distributions of macropore system and different matrix properties. The main result was that the formation factor of dual-pore network obeyed a ‘universal’ scaling relationship (i.e. independent of lattice type). Based on this result, we extended the power-law model derived by Bernabé et al. for monomodal porous media. We developed methods for evaluating the scale-invariant pore structure parameters in the model using conventional core analysis and satisfactorily tested the proposed model against experimental data from the Chinese reservoir as well as some other previously published data sets.
Klinkenberg-corrected gas permeability (k∞) and liquid permeability (kl) are usually considered equal and used to describe the intrinsic permeability of reservoirs. In this study, permeabilities of 30 outcrop Fontainebleau sandstones were measured using nitrogen gas and distilled water at room temperature. As a result, k∞ was times larger than kl, presence of liquid-matrix coupling and thin water films were considered to be the primary reasons. A universal permeability model based on percolation network model was introduced and the simulated permeability was obtained to compare kl and k∞, which indicated that k∞ was more suitable for characterizing the intrinsic permeability.
Electrical resistivity is one of the fundamental physical properties of rocks, and its relationship with fluid saturation is widely used in reservoir evaluation. The interpretation of electrical logs usually relies on the results of rock resistivity tests of cores in the laboratory. In the laboratory, core samples are commonly cut into cylinders, and the resistivity is measured along the axial direction. To determine the rock resistivity along different directions, samples are cut into cubes and tested along three perpendicular directions to obtain resistivity data. The expensive and complicated preparation process of cubic samples and the custom holder requirements limit the use of these tests. We have analyzed the advantages and disadvantages of rock resistivity measurements of cylindrical and cubic samples. To overcome the abovementioned difficulties, we develop a core holder for radial resistivity measurements and a radial resistivity measurement method for cylindrical samples. Based on the conformal transformation of the complex variable function theory, we establish a mathematical model of radial resistivity. We develop a measurement method of radial resistivity according to the mathematical model and verify this approach with isotropic cores. The theoretical calculation results agree with the experimental results. With the radial resistivity measurement method, we effectively test the resistivity anisotropy of shale. This method has more advantages than existing methods in terms of the sample preparation and realization of various displacement levels and angles. Hence, the proposed method can be widely used.
Effective stress coefficient for permeability (ESCK) is the key parameter to evaluate the properties of reservoir stress sensitivity. So far, little studies have clarified which ESCK is correct for a certain reservoir while rock ESCK is measured differently by different fluid media. Thus, three different fluids were taken to measure a fine sandstone sample’s ESCK, respectively. As a result, the ESCK was measured to be the smallest by injecting nitrogen, the largest by injecting water, and between the two by brine. Besides, those microcharacteristics such as rock component, clay mineral content, and pore structure were further analyzed based on some microscopic experiments. Rock elastic modulus was reduced when water‐sensitive clay minerals were encountered with aqua fluid media so as to enlarge the rock ESCK value. Moreover, some clay minerals reacting with water can spall and possibly block pore throats. Compared with water, brine can soften the water sensitivity; however, gas has no water sensitivity effects. Therefore, to choose which fluid medium to measure reservoir ESCK is mainly depending on its own exploitation conditions. For gas reservoirs using gas to measure ESCK is more reliable than water or brine, while using brine is more appropriate for oil reservoirs.