Traditional timber harvests on steep slopes have been conducted through labor-intensive and sometimes environmentally impactful methods, such as manual felling with chainsaws and extraction using bladed skid trails, winching, or cable yarding. Ground-based mechanized harvesting and primary transportation methods such as cut-to-length harvesters and forwarders have emerged in some parts of the world as low-impact, safe, and efficient alternatives to the aforementioned systems. However, when mechanized operations are used on steep terrain, problems such as poor stability, loss of traction, and increased soil disturbance can occur. Tethered or winch-assisted logging practices are being tested and applied in several countries to adapt to challenges associated with operating equipment on steep slopes while minimizing environmental impact. To better understand the feasibility of these systems, we conducted a designed experiment to quantify changes in soil properties and predicted erosion resulting from varying numbers of passes and payload levels by a forwarder operating on slopes ranging from 27 to 38 degrees. The machine was equipped with two different track configurations, tethered by either a machine-mounted or self-contained winch, in eucalyptus plantations in Brazil. On low slopes, bulk density significantly increased, but it did not increase on steeper slopes; this demonstrates traction winches’ effectiveness at reducing concentrated ground pressures. Rut depths were minimal and decreased with increasing slope classes due to reduced track slippage. Predicted erosion rates were high, primarily due to the extremely steep, long slopes and lack of adequate cover in some portions of the trail, illustrating the importance of proper erosion management practices on steep slopes.

Woody biomass is an important feedstock for renewable energy production in the United States. Residues are produced by forest harvests, and some operations utilize this material for energywood. Energywood requires additional processing and is often the lowest value product generated. Additional research quantifying the productivity and costs of energywood operations could allow stakeholders to evaluate the efficiency of those operations and identify areas for improvement. This study evaluated five energywood harvesting operations in the Lower Mid-Atlantic region of the United States (two Appalachian Mountain harvests and three Coastal Plain harvests). Each harvesting operation was observed for 4–7 days, and productivity data were collected on each harvesting function using time study and activity sampling methods. Productivity and costs of each operation were estimated, and equipment mixes and harvesting methods were evaluated to determine efficiency. Interviews were also conducted with each logging contractor to understand operating strategies and decision making. Cut and haul costs averaged (USD) $32.07/tonne and ranged from $26.19 to $38.28/tonne. Hauling consistently comprised the largest function cost at an average of $12.24/tonne. Machines handling energywood were less productive than those harvesting roundwood because of the large effect average stem size had on productivity levels. Harvesting system analysis also highlighted the importance of ensuring a balanced equipment mix to lower costs and ensure efficiency. This research provides stakeholders with a valuable comparison of energywood harvesting operations in the Lower Mid-Atlantic region of the United States that can be used to make better-informed decisions regarding the efficient and economical harvest of energywood.

Water quality best management practices (BMPs) developed for conventional forest harvests may be adequate for biomass harvests, yet quantitative data is lacking. This study compared estimated erosion, operational feature areas, BMP implementation rates, ground cover characteristics, and downed woody debris quantities following biomass and conventional harvests in the mountains of Virginia. Haul roads on biomass harvests had significantly higher estimated erosion rates (P = 0.064) and masses (P = 0.045) than conventional harvests, but conventional harvests had higher erosion contributions from skid trails (P = 0.089) and averaged more estimated erosion mass overall, despite being significantly smaller in size (P = 0.054). There was significantly less area in heavy slash (P = 0.076) and lower estimated mass of residual downed woody debris (P = 0.001) on biomass sites than conventional sites (10.98 and 27.95 tons/ac, respectively). Site-wide BMP implementation scores (P = 0.041), streamside management zones (SMZs) (P = 0.024), and skidding (P = 0.063) were significantly higher on biomass sites than conventional sites. BMP implementation scores were significant predictors of estimated erosion rates (P < 0.001, R² = 59%), indicating that adequate levels of existing water quality BMPs are effective for erosion control on both conventional and biomass harvests.

Expanding markets for renewable energy feedstocks have increased demand for woody biomass. Concerns associated with forest biomass harvesting include increased erosion, the applicability of conventional forestry Best Management Practices (BMPs) for protecting water quality, and reduced woody debris retention for soil nutrients and cover. We regionally compared the data and results from three prior independent studies that estimated erosion, BMP implementation, and residual woody debris following biomass and conventional forest harvests in the Mountains, Piedmont, and Coastal Plain of Virginia. Estimated erosion was higher in the Mountains due to steep slopes and operational challenges. Mountain skid trails were particularly concerning, comprising only 8.47% of the total area but from 37.9 to 81.1% of the total site-wide estimated erosion. BMP implementation varied by region and harvest type, with biomass sites having better implementation than conventional sites, and conventional Mountain sites having lower implementation than other regions. Sufficient woody debris remained for BMPs on both harvest types in all regions, with conventional Mountain sites retaining twice that of Coastal Plain sites. BMPs reduced the estimated erosion on both site types suggesting increased implementation could reduce potential erosion in problematic areas. Therefore, proper BMP implementation should be ensured, particularly in Mountainous terrain, regardless of harvest type.