The zona pellucida (ZP) is the spherical layer that surrounds the mammalian oocyte. The physical hardness of this layer plays a crucial role in fertilization and is largely unknown because of the lack of appropriate measuring and modelling methods. The aim of this study is to measure the biomechanical properties of the ZP of human/mouse ovum and to test the hypothesis that Young's modulus of the ZP varies with fertilization. Young's moduli of ZP are determined before and after fertilization by using the micropipette aspiration technique, coupled with theoretical models of the oocyte as an elastic incompressible half-space (half-space model), an elastic compressible bilayer (layered model) or an elastic compressible shell (shell model). Comparison of the models shows that incorporation of the layered geometry of the ovum and the compressibility of the ZP in the layered and shell models may provide a means of more accurately characterizing ZP elasticity. Evaluation of results shows that although the results of the models are different, all confirm that the hardening of ZP will increase following fertilization. As can be seen, different choices of models and experimental parameters can affect the interpretation of experimental data and lead to differing mechanical properties.

Coronary artery disease is responsible for a third of global deaths worldwide. Computational simulations of blood flow can be used to understand the interactions of artery/plaque and blood in coronary artery disease and to better predict the rupture of atherosclerotic plaques. So far, the mechanical properties of animals' coronary artery have been mostly used for hemodynamic simulation of atherosclerotic arteries. The mechanical properties of animals' coronary arteries are often not accurate enough and can be only used for an approximate estimation and comparative assessment of the cognate parameters in human. In this study, a three-dimensional (3D) computational fluid-structure interactions model with three different plaque types is presented to perform a more accurate plaque vulnerability assessment for human atherosclerotic plaques. The coronary arteries of twenty-two male individuals were removed during autopsy and subjected to uniaxial tensile loading. The hyperelastic material coefficients of coronary arteries were calculated and implemented to the computational model. The fully coupled fluid and structure models were solved using the explicit dynamics finite element code LS-DYNA. The normal and shear stresses induced within the plaques were significantly affected by different plaque types. The highest von Mises (153 KPa) and shear (57 KPa) stresses were observed for hypocellular plaques, while the lowest von Mises (70 KPa) and shear (39 KPa) stresses were observed on the stiffer calcified plaques. The results suggest that the risk of plaque rupture due to blood flow is lower for cellular and hypocellular plaques, while higher for calcified plaques with low fracture stresses.

As a main cause of mortality in developed countries, Coronary Artery Disease (CAD) is known as silent killer with a considerable cost to be dedicated for its treatment. Coronary Artery Bypass Graft (CABG) is a common remedy for CAD for which different blood vessels are used as a detour. There is a lack of knowledge about mechanical properties of human blood vessels used for CABG, and while these properties have a great impact on long-term patency of a CABG. Thus, studying these properties, especially those of human umbilical veins which have not been considered yet, looks utterly necessary. Umbilical vein, as well as human Saphenous vein, are respectively obtained after cesarean and CABG. First, histological tests were performed to investigate different fiber contents of the samples. Having prepared samples carefully, force-displacement results of samples were rendered to real stress–strain measurements and then a fourth-order polynomial was used to prove the non-linear behavior of these two vessels. Results were analyzed in two directions, i.e. circumferentially and longitudinally, which then were compared with each other. The comparison between stiffness and elasticity of these veins showed that Saphenous vein’s stiffness is much higher than that of umbilical vein and also, it is less stretchable. Furthermore, for both vessels, longitudinal stiffness was higher than that of circumferential and in stark contrast, stretch ratio in circumferential direction came much higher than longitudinal orientation. Blood pressure is very high in the region of aorta, so there should be a stiff blood vessel in this area and previous investigations showed that stiffer vessels would have a better influence on the flow of bypass. To this end, the current study has made an attempt to compare these two blood vessels’ stiffness, finding that Saphenous vein is stiffer than umbilical vein which is somehow as stiff as rat aortic vessels. As blood vessel’s stiffness is directly related to elastin and mainly collagen content, results showed the lower amount of these two contents in umbilical vein regarding Saphenous vein.

Gelatin (Gel) has been reported as a promising candidate in tissue engineering owing to its easy availability, biocompatibility, and biodegradability. Gel hydrogel is of potential to be cross-linked with different materials to enhance their biocompatibility for cell culture for tissue engineering applications. The mechanical properties of this versatile material, however, have not been thoroughly determined. In this study, the linear elastic (Young’s modulus and maximum stress) and non-linear hyperelastic (hyperelastic coefficients) mechanical properties of prepared hydrogels at different contents of Gel (wt%) were measured, and its Young’s modulus was compared with that of skin tissue. The prepared cylindrical Gel hydrogels were subjected to a series of unconfined compression tests. The hyperelastic strain energy density function was calibrated using the compressive experimental data. The potential ability of the Yeoh hyperelastic constitutive equation, which has been proposed as the best material model to represent the non-linear behavior of hydrogels, was verified using finite element (FE) simulations. The results revealed that the Young’s modulus and maximum stress of hydrogels are increased by the addition of Gel. The highest Young’s modulus (81 kPa) and maximum stress (24 kPa) were observed for hydrogels with 15 wt% Gel. Results also showed that the hydrogels with a relatively lower content (7.5 wt%) for skin tissue engineering. The Yeoh material model was closely fitted with the experimental data and could be used in further biomechanical simulations of the hydrogels. The experimental results were also compared well with those predicted by the FE models. The results of this study might have implications not only for the understanding of the mechanical properties of Gel hydrogel but also for the fabrication of polymeric substrate materials suitable for skin tissue engineering applications.