The stability of water-preventing coal pillar plays an important role in preventing gob water inrush. The gob side of the water-preventing coal pillar is soaked in a certain height of mine water. Different soaking heights may affect the stability of coal pillars. Few studies have been conducted on the properties of coals with different water-soaking heights. We carried out uniaxial compressive tests on coal specimens with different water-soaking heights to gain a better understanding of different water-soaking-height-induced weakening characteristics of coal. Results show that: (1) The water content of coal specimens increases with the soaking height. Water significantly weakens the strength of coal specimens. However, the extent of strength weakening of the coal specimen does not increase with the increase of the soaked height. The strength of the fully soaked coal specimen is lowest among all groups of coal specimens. The strength of the three groups of partially soaked coal specimens is between the fully soaked coal specimens and the coal specimens without being soaked in the water. In the three groups of partially soaked coal specimens, the strength of the coal specimens increases with the increase of the soaking height. (2) The acoustic emission activities of complete water soaking and nonsoaking coal specimens are relatively concentrated, occurring mainly in unstable fracture expansion stage and post-peak destruction stage, and acoustic emission exhibits main-shock mode. Partially soaking coal specimens, especially the 25% water-soaking height and 50% water-soaking height coal specimens, produces obvious acoustic emission activities during the fracture expansion stabilization phase, and then generates more acoustic emission activities during the unstable expansion stage and the post-peak stage. The acoustic emission presents foreshock—main shock mode. (3) The softening effect of the water soaking on the coal specimens is obvious. It was further found that the deformation of coal specimens with partial water soaking is not synchronized in different layers, the nonuniform deformations of partially soaked coal specimens aggravate its damage.
In underground engineering, shear failure is a common failure type in coal-rock mass under medium and low strain-rate disturbance loads. Analyzing the shear failure mechanical properties of coal-rock mass under dynamic normal load is significant. In order to reveal the influence of disturbance load on the shear mechanical properties of coal rock, a dynamic and static load coupling electro-hydraulic servo testing machine was used to conduct the shear tests of coal-like rock materials under dynamic and constant normal load. The amplitude of dynamic load is 10 kN and the frequency is 5 Hz. The damage process of the specimens was detected by the acoustic emission (AE) detection system. The results imply that the shear failure process of coal-like rock materials under constant normal load can be divided into four stages. The normal disturbance decreased the shear strength of the specimens and increased the shear modulus of the specimens. With the increase in normal load, the influence of disturbance on the shear strength of the specimen decreased. By analyzing the AE parameters, it was found that the dynamic load made the internal damage of the specimen more severe during the shear failure process. The damage variable was calculated by AE cumulative energy, and the damage evolution was divided into three stages. The shear failure mechanism of the specimen was judged by RA (rise time/amplitude) and AF (average frequency). It was found that from the elastic deformation stage to the unstable development fracture stage, the proportion of shear fracture increased. When the dynamic normal load was 10 kN and 30 kN, the fracture was mainly shear fracture; When the dynamic normal load was 50 kN, the fracture was mainly tensile or mixed fracture. The dynamic normal load affects the shear strength and failure mechanism. Therefore, the influence of disturbance load on coal-rock mass strength cannot be ignored in underground engineering.
Retained gob-side entry (RGE) is a significant improvement for fully-mechanized longwall mining. The environment of surrounding rock directly affects its stability. Roadside backfilling body (RBB), a man-made structure in RGE plays the most important role in successful application of the technology. In the field, however, the vertical deformation of RBB is large during the panel extraction, which leads to malfunction of the RGE. In order to solve the problem, roof pre-split is employed. According to geological conditions as well as the physical modeling of roof behavior and deformation of surrounding rock, the support resistance of RBB is calculated. The environment of surrounding rock, vertical stress and vertical deformation of the RBB in the RGE with different roof pre-split angles are analyzed using FLAC3D software. With the increase of roof pre-split angle, the vertical stresses both in the coal wall and RBB are minimum, and the vertical deformation of RBB also decreases from 110.51 mm to 6.1 mm. Therefore, based on the results of numerical modeling and field observation, roof pre-split angle of 90° is more beneficial to the maintenance of the RGE.