Pierre Cerasi

Dr. Pierre Cerasi


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 March 2021 in Materials
Verified
Journal Article
Open access
PDF file
KGKamila Gawel
Kamila Gawel
DSDawid Szewczyk
Dawid Szewczyk
PCPierre Cerasi
Pierre Cerasi
Chemical reactions with reservoir fluids and geology related in-situ stress changes may cause damages to cement sealing material in plugged and abandoned oil, gas and CO2 wells. To avoid leakages, a legitimate monitoring technique is needed that could allow for early warning in case such damages occur. In this paper, we test the utility of oil and gas well cement with a conductive filler in sensing stress changes. To this end, we have measured the resistance response of Portland G—oil and gas well cement with carbon nanofibers (CNF) to axial load during uniaxial compressive strength test. Simultaneously, the microseismicity data were collected. The resistance of the nanocomposite was measured using two-point method in the direction of loading. The resistance changes were correlated with acoustic emission events. A total of four different material response regions were distinguished and the resistivity and acoustic emission changes in these regions were described. Our results suggest that the two complementary methods, i.e., acoustic emission and resistance measurements, can be used for sensing stress state in materials including well cement/CNF composites. The results suggest that the well cement/CNF composites can be a good candidate material to be used as a transducer sensing changes in stress state in, e.g., well plugs up to material failure.

7 September 2019 in Energies
Verified
Journal Article
Open access
PDF file
MRMats Rongved
Mats Rongved
PCPierre Cerasi
Pierre Cerasi
CO2 sequestration projects will in the coming years include both aquifer and depleted oil and gas field sites, with different stress paths and history. Stress changes and stress concentration effects on faults will have to be readily assessed, potentially endangering shallower permeable formations. Usually, a fault is modeled as a singularity with shear strength or friction properties, and simulations are run to determine whether the fault is reactivated through shear failure. In this paper, we model a simple rectilinear fault as a finite surface with lowered mechanical properties compared to elsewhere in the domain, which represents a fractured zone alongside the fault core. SINTEF’s Modified Discrete Element code is used coupled to the flow simulator TOUGH2, to model the fracture initiation and propagation, monitoring the permeability increase along the fault. A simplified scenario is simulated, with a sandstone storage reservoir bounded by a fault, penetrating a shale caprock to a shallower sandstone layer. The storage site either undergoes depletion before CO2 injection or has its pore pressure increased to simulate the case of aquifer storage. Results show that during depletion, shear stresses may develop such that fractures propagate alongside the fault to the upper aquifer. However, for the mirror fault orientation with regards to verticality, no such fractures develop. These results are reversed for the aquifer storage case.

13 September 2022 in Physical Sciences Forum
Verified
Conference Paper
Open access
PDF file
PCPierre Cerasi
Pierre Cerasi
MDMarcin Duda
Marcin Duda
LELaura Edvardsen
Laura Edvardsen
NANicolaine Agofack
Nicolaine Agofack
MBMohammad Bhuiyan
Mohammad Bhuiyan
Laboratory tests were performed on the Draupne shale formation, which may serve as a seal over CO2 storage sites. Different techniques were used to assess the integrity and mechanical properties of the shale, with the main objective of investigating whether exposure to CO2 would in any manner alter these properties. The laboratory methods used encompass traditional triaxial tests; however, with fluid substitution prior to increasing axial stress to failure. These tests were conducted on smaller cylindrical plugs than standard, taking advantage of the finer grained nature of the shale. Another set of experiments used the low-frequency technique, whereby small amplitude, cyclic axial strains are applied on the specimen, allowing a direct measurement of stiffness. Long exposure, with change of fluid from brine to CO2, allowed for quantifying small changes in stiffness, thanks to the many repeated cycles of non-destructive testing. In a final experimental technique, the punch test, shear strength of the same material was obtained by cutting a central disk from a larger intact shale disk, while measuring the shear force needed to perform the cut.