João Mouro

Dr. João Mouro

INESC Microsistems and Nanotechnologies, 1000-029 Lisboa, Portugal
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 December 2020 in Sensors
Verified
Journal Article
Open access
PDF file
João MouroJoão Mouro
João Mouro
Rui M. R. PintoRui M. R. Pinto
Rui M. R. Pinto
Paolo PaolettiPaolo Paoletti
Paolo Paoletti
Bruno TiribilliBruno Tiribilli
Bruno Tiribilli
A microcantilever is a suspended micro-scale beam structure supported at one end which can bend and/or vibrate when subjected to a load. Microcantilevers are one of the most fundamental miniaturized devices used in microelectromechanical systems and are ubiquitous in sensing, imaging, time reference, and biological/biomedical applications. They are typically built using micro and nanofabrication techniques derived from the microelectronics industry and can involve microelectronics-related materials, polymeric materials, and biological materials. This work presents a comprehensive review of the rich dynamical response of a microcantilever and how it has been used for measuring the mass and rheological properties of Newtonian/non-Newtonian fluids in real time, in ever-decreasing space and time scales, and with unprecedented resolution.

4 March 2020 in Nature Communications
Verified
Journal Article
Open access
PDF file
SRSunil Rana
Sunil Rana
João MouroJoão Mouro
João Mouro
SBSimon J. Bleiker
Simon J. Bleiker
JRJamie D. Reynolds
Jamie D. Reynolds
HCHarold M. H. Chong
Harold M. H. Chong
DPDinesh Pamunuwa
Dinesh Pamunuwa
Emerging applications such as the Internet-of-Things and more-electric aircraft require electronics with integrated data storage that can operate in extreme temperatures with high energy efficiency. As transistor leakage current increases with temperature, nanoelectromechanical relays have emerged as a promising alternative. However, a reliable and scalable non-volatile relay that retains its state when powered off has not been demonstrated. Part of the challenge is electromechanical pull-in instability, causing the beam to snap in after traversing a section of the airgap. Here we demonstrate an electrostatically actuated nanoelectromechanical relay that eliminates electromechanical pull-in instability without restricting the dynamic range of motion. It has several advantages over conventional electrostatic relays, including low actuation voltages without extreme reduction in critical dimensions and near constant actuation airgap while the device moves, for improved electrostatic control. With this nanoelectromechanical relay we demonstrate the first high-temperature non-volatile relay operation, with over 40 non-volatile cycles at 200 ∘C.

4 April 2025 in npj 2D Materials and Applications
Verified
Journal Article
Open access
PDF file
João MouroJoão Mouro
João Mouro
TDTelma Domingues
Telma Domingues
TPTiago Pereira
Tiago Pereira
RCRui Campos
Rui Campos
JBJérôme Borme
Jérôme Borme
PAPedro Alpuim
Pedro Alpuim
Electrolyte-gated graphene field-effect transistors are increasingly attractive as platforms for high-sensitivity and low-detection limit biosensing or in synaptic or memristive elements used in neuromorphic computing. However, their electrical stability and noise have yet to be thoroughly analyzed and understood. In this work, we have undertaken a comprehensive experimental characterization of the dynamic response of the drift in electrolyte-gated graphene field-effect transistors under various measurement conditions. We then developed an analytical model, which was phenomenologically validated for all observed drift phenomena and fitted to the experimental data. The model is based on charge trapping at the silicon oxide substrate defects in contact with the graphene channel. The electron transitions are made possible by the absorption of phonons to overcome the energetic barrier leading to the new state. This in-depth understanding of these devices’ responses is essential to fully exploit their behavior in applications and standardize practices amongst the community.

14 November 2013 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
João MouroJoão Mouro
João Mouro
AGA. Gualdino
A. Gualdino
VCVirginia Chu
Virginia Chu
JCJoao P. Conde
Joao P. Conde
Thin-film silicon allows the fabrication of MEMS devices at low processing temperatures, compatible with monolithic integration in advanced electronic circuits, on large-area, low-cost, and flexible substrates. The most relevant thin-film properties for applications as MEMS structural layers are the deposition rate, electrical conductivity, and mechanical stress. In this work, n+-type doped hydrogenated amorphous and nanocrystalline silicon thin-films were deposited by RF-PECVD, and the influence of the hydrogen dilution in the reactive mixture, the RF-power coupled to the plasma, the substrate temperature, and the deposition pressure on the structural, electrical, and mechanical properties of the films was studied. Three different types of silicon films were identified, corresponding to three internal structures: (i) porous amorphous silicon, deposited at high rates and presenting tensile mechanical stress and low electrical conductivity, (ii) dense amorphous silicon, deposited at intermediate rates and presenting compressive mechanical stress and higher values of electrical conductivity, and (iii) nanocrystalline silicon, deposited at very low rates and presenting the highest compressive mechanical stress and electrical conductivity. These results show the combinations of electromechanical material properties available in silicon thin-films and thus allow the optimized selection of a thin silicon film for a given MEMS application. Four representative silicon thin-films were chosen to be used as structural material of electrostatically actuated MEMS microresonators fabricated by surface micromachining. The effect of the mechanical stress of the structural layer was observed to have a great impact on the device resonance frequency, quality factor, and actuation force.

18 October 2021 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
João MouroJoão Mouro
João Mouro
MFMafalda Ferreira
Mafalda Ferreira
ASAna V. Silva
Ana V. Silva
DLDiana C Leitao
Diana C Leitao
Recent paradigms, such as smart cities/homes, Internet of Things or portable and implantable healthcare systems, require the use of flexible and conformal sensors that can be assembled to arbitrarily 3D complex shapes. A good set of simple and available models is of paramount importance to help designing and fabricating such devices. In this work, analytical expressions for the bending plane, the curvature radii and the stress/strain distributions of multilayer composite devices are derived for the cases of uniaxial and biaxial plane stress and plane strain and generalised plane strain. The analytical results are summarized, and two case-studies are analysed and compared with the help of these models: bilayer and trilayer hinges for self-assembled structures and rolled up flexible substrates with sensors on top. The dependence of the curvature radii and strain and stress distributions on several mechanical properties of the composite is assessed. The applicability of these models to support the design of flexible sensors, electronics or haptic devices is discussed and their practical limitations analysed.

2 October 2017 in Applied Physics Letters
Verified
Journal Article
Open access
João MouroJoão Mouro
João Mouro
Bruno TiribilliBruno Tiribilli
Bruno Tiribilli
Paolo PaolettiPaolo Paoletti
Paolo Paoletti
A viscosity sensor based on the nonlinear behaviour of a microcantilever embedded in a self-excitation loop with an adjustable phase-shifter is proposed. The self-sustained oscillation frequencies of the cantilever are experimentally and theoretically investigated as functions of the fluid viscosity and of the imposed phase shift of the signal along the self-excitation loop. The sensor performance is validated experimentally using different water-glycerol solutions. In contrast to existing rheological sensors, the proposed platform can be tuned to work in two different modes: a high-sensitivity device whose oscillation frequency changes smoothly with the rheological properties of the fluid or a critical viscosity threshold detector, where, for small changes in fluid viscosity, there is a step change in oscillation frequency.