Surface imprinting used for protein recognition in functional cavities is highly effective in imprinting biomacromolecules to avoid template encapsulation during the formation of a molecularly imprinted polymer (MIP) matrix. Herein, we introduce a facile surface-imprinting method based on two-step spin-coating and photopolymerization to design highly efficient imprinted sites on polymeric films to detect trypsin (TRY). Well-distributed template imprinting is successfully achieved for maximized sensing responses by controlling the composition of functional monomers and crosslinkers in the precursor solution and the concentration of TRY in the imprinting solution. The MIP film exhibits higher sensitivity (−841 ± 65 Hz/(μg/mL)) with a coefficient of determination of 0.970 and a higher imprinting factor of 4.5 in a 0.24 µg/mL TRY solution compared to the nonimprinted polymer (NIP) film. Moreover, the limit of detection and limit of quantification are calculated to be 25.33 and 84.42 ng/mL, respectively. Finally, the selectivity coefficient is within the range of 3.90–6.78 for TRY against other proteins. These sensing properties are superior to those of the corresponding nonimprinted polymer matrix. Thus, the proposed facile surface-imprinting method is highly effective for protein imprinting with high sensitivity and selectivity.
Surface imprinting used for template recognition in nanocavities can be controlled and improved by surface morphological changes. Generally, the lithographic technique is used for surface patterning concerning sensing signal amplification in molecularly imprinted polymer (MIP) thin films. In this paper, we describe the effects of silanized silica molds on sensing the properties of MIP films. Porous imprinted poly(MAA–co–EGDMA) films were lithographically fabricated using silanized or non-treated normal silica replica molds to detect 2,4-dichlorophenoxyacetic acid (2,4-D) herbicide as the standard template. The silanized mold MIP film (st-MIP) (Δf = −1021 Hz) exhibited a better sensing response than the non-treated normal MIP (n-MIP) (Δf = −978 Hz) because the imprinting effects, which occurred via functional groups on the silica surface, could be reduced through silane modification. Particularly, two non-imprinted (NIP) films (st-NIP and n-NIP) exhibited significantly different sensing responses. The st-NIP (Δfst-NIP = −332 Hz) films exhibited lower Δf values than the n-NIP film (Δfn-NIP = −610 Hz) owing to the remarkably reduced functionality against nonspecific adsorption. This phenomenon led to different imprinting factor (IF) values for the two MIP films (IFst-MIP = 3.38 and IFn-MIP = 1.86), which was calculated from the adsorbed 2,4-D mass per poly(MAA–co–EGDMA) unit weight (i.e., QMIP/QNIP). Moreover, it was found that the st-MIP film had better selectivity than the n-MIP film based on the sensing response of analogous herbicide solutions. As a result, it was revealed that the patterned molds’ chemical surface modification, which controls the surface functionality of imprinted films during photopolymerization, plays a role in fabricating enhanced sensing properties in patterned MIP films.
Surface imprinting is an effective and simple method to fabricate and retain imprinted templates and recognizable nanocavities after template extraction. The imprinted effects can be controlled depending on the surface morphological changes. In general, a planar film has a limited area compared to a structured film with relatively higher surface-to-volume (S/V) ratio (A/A0), leading to the conventional sensing response upon the functionality of monomers in a fixed chemical composition. To increase the limited sensing properties and develop simple fabrication of porous arrays on a large area, we herein demonstrate the 2,4-dichlorophenoxyacetic acid (2,4-D, herbicide)-imprinted porous thin film lithographically patterned using photopolymerization and silica colloidal array as a master mold, derived by a unidirectional rubbing method. The resonant frequency changes with respect to the adsorption of 2,4-D molecules on a template-extracted porous poly(MAA-co-EGDMA) (MIP) film in a 10−1 mM aqueous solution of 2,4-D for 1 h, and when compared to the planar MIP film, the higher sensing response (Δf = −283 ± 7 Hz ≈ 1543 ± 38 ng/cm2) appears on the porous MIP film due to the specific recognition toward the more accessible templated cavities of the structured porous array, indicating an imprinting effect (If) value of 3.5. In addition, a higher selectivity for 2,4-D was also displayed on the porous MIP film compared to other herbicides. From these results, it was revealed that these improved sensing properties can be determined from the effects of various parameters (template functionality, film structuring, hydroxyl groups of silica colloids, etc.).