Spray sprinklers enable to operate at low pressures (<103 kPa) in self-propelled irrigation machines. A number of experiments were performed to characterize the water distribution pattern of an isolated rotator spray plate sprinkler operating at very low pressure under different experimental conditions. The experiments were performed under two pressures (69 kPa and 103 kPa) and in calm and windy conditions. The energy losses due to the impact of the out-going jet with the sprinkler plate were measured using an optical technique. The adequacy to reproduce the measured water distribution pattern under calm conditions of two drop size distribution models was evaluated. A ballistic model was used to simulate the water distribution pattern under wind conditions evaluating three different drag models: (1) considering solid spherical drops; (2) a conventional model based on wind velocity and direction distortion pattern, and (3) a new drag coefficient model independent of wind speed. The energy losses measured with the optical method range from 20% to 60% from higher to lower nozzle sizes, respectively, for both evaluated working pressures analyzing over 16,500 droplets. For the drop size distribution selected, Weibull accurately reproduced the water application with a maximum root mean square error (RMSE) of 19%. Up to 28% of the RMSE could be decreased using the wind-independent drag coefficient model with respect to the conventional model; the difference with respect to the spherical model was 4%.

Inefficient management of dissolved oxygen (DO) in intensive aquaculture systems limits fish welfare and productivity by creating oxygen-deficient zones and promoting hydrodynamic conditions that hinder their dispersion. Because water movement directly influences how oxygen is transported and mixed within the culture unit, inadequate flow management can allow localized hypoxia to persist even when total oxygen input appears sufficient. To address this issue, this study proposes an integrated methodology that combines in situ respirometry measurements with Computational Fluid Dynamics (CFD) simulations to evaluate the spatial distribution of DO and diagnose the operational performance of aquaculture systems. The methodology quantifies oxygen consumption using intermittent-flow respirometry, applies a three-dimensional two-phase CFD model (water–oxygen) incorporating experimental oxygen consumption rates as boundary conditions, and validates the model under real operating conditions, focusing on active metabolism as the most demanding physiological state. The model generates a spatial distribution of DO patterns that are significantly modified by pond geometry, water flow characteristics, the metabolism of the fish and fish positioning. The differences between experimental and simulated values ranged from 7.8% to 10.7%, confirming the accuracy of the proposed method. The integration of in situ metabolic measurements with CFD modeling provides a realistic representation of DO dynamics, enabling system optimization and promoting more efficient and sustainable aquaculture.

The interaction between circular piers and turbulent open-channel flow generates complex three-dimensional structures, including horseshoe vortices at the pier base and wake vortices downstream. These structures increase vertical velocities, pressure fluctuations, and shear stresses, contributing to erosion and structural instability. Although these phenomena have been widely studied, limited attention has been given to surface geometric modifications as a flow-control strategy. This study employs Large Eddy Simulation (LES) to evaluate the influence of a hexagonal dimple pattern on circular piles in a free-surface channel. The dimples were defined by varying diameter, depth, and spacing to reduce vertical velocity and alter vortex formation. The computational domain represents a 0.40 m wide, 12 m long, and 1.2 m high rectangular channel, with an inlet mass flow of 9.4 kg/s and 0.10 m water depth. Model validation against particle image velocimetry (PIV) data showed 99% correlation, confirming numerical accuracy. Results demonstrate that textured surfaces modify flow dynamics by enhancing kinetic energy dissipation and generating micro-vortices that weaken dominant structures. The optimal configuration (6 mm diameter, 2 mm depth, 1 mm spacing) reduced downward vertical velocity by 42% and wake vortex shedding frequency by 24%, indicating improved hydraulic stability and erosion mitigation potential.

Wind energy has become an essential resource for the development and diversification of the energy sector in México and worldwide. In this context, the mechanical design of turbine blades has emerged as a priority research topic, given its impact on performance and viability. The present research evaluates the aero-structural response of multiple lay-up configurations of a 6 m blade by coupling computational fluid dynamics (CFD) and finite element analysis (FEA). The fluid–structure interaction (FSI) was simulated in ANSYS, a commercial software chosen for its capacity for multivariable analysis. The nominal operating conditions included a wind speed of 10.5 m/s and a rotational speed of 100 rpm, leading to a theoretical power output of 6591 W. For the proposed lay-up configurations, the Tsai-Wu and Puck (Global IRF) criteria were estimated and remained below the critical threshold of 1.0, indicating no risk of structural failure. However, some carbon fiber/epoxy layers, including unidirectional layers in the spar caps and bidirectional layers in the structural shear web, may present failure risks under extreme loading conditions. This applies to configurations with the lowest number of layers in the mid-span spar caps; this fact is reinforced by the main effects analysis. The results emphasize the relevance of conducting comprehensive composite failure evaluations to optimize material selection and structural design, even for small-scale blades.