The textile industry is one of the largest consumers of water in the world and its wastewater is a serious problem when it is discharged without the proper treatment. In this work, wastewater generated by textile industry was treated coupling a homogenization–decantation treatment with polyvinylidene difluoride (PVDF) ultrafiltration membranes. Initially, the wastewater was aerated in a homogenization–decantation tank where 17% colour and 10% chemical oxygen demand (COD) were removed. The aerated effluent was treated with an ultrafiltration membrane in order to reuse the permeate in new dyeing processes. Firstly, the ultrafiltration treatment was performed in a laboratory plant. The permeate analysis showed 20% colour removal and 60% COD decrease. On the basis of these results, a semi-industrial system was built. With this plant, the permeate characterization showed similar results. The system was found to be scalable and suitable for the treatment of this kind of effluents. Finally, new dyeings were performed with both permeates. Monochromatic dyeings were carried out with 100% permeate whereas 50% permeate was reused for dyeings with a mixture of three dyes. The colour differences were found to be lower than 1.5, which was the acceptance value establishedPostprint (author's final draft
The reactive dye Cibacron Yellow S-3R was selected to evaluate the feasibility of combining nanofiltration membranes with electrochemical processes to treat textile wastewater. Synthetic dyeing effluents were treated by means of two nanofiltration membranes, Hydracore10 and Hydracore50. Up to 98% of dye removal was achieved. The influence of salt concentration and pH on membrane treatment was studied. The best dye removal yield was achieved at pH 3 in the presence of 60 g/L of NaCl. After the membrane filtration, the concentrate containing high dye concentration was treated by means of an electrochemical process at three different current densities: 33, 83, and 166 mA/cm2. Results showed a lineal relationship between treatment time and applied current density. Both permeates and electrochemically-decoloured effluents were reused in new dyeing processes (100% of permeate and 70% of decoloured concentrates). Dyed fabrics were evaluated with respect to original dyeing. Colour differences were found to be into the acceptance range.
Indigo is one of the most consumed dyes in the textile sector, as it is widely used for the dyeing of denim clothes. About 15% of indigo used in the dyeing process is discharged to the wastewater treatment plants or sometimes into rivers, in countries where regulations are not strictly applied. In this work, real effluents that contained indigo dye were treated by means of 4 different ultrafiltration membranes. The feasibility to recover the concentrated dye with lab and semi-industrial pilots was also investigated. The studied membranes achieved up to 99% colour removal and 80% chemical oxygen demand (COD) decrease. Finally, the concentrates containing 20 g L_1 of indigo dye were reused in new dyeing processes. Colour differences (DECMC) and rubbing and washing fastnesses were evaluated. Fabrics dyed with the recovered indigo concentrates exhibited similar characteristics than the ones obtained with the commercial dyePostprint (author's final draft
After the dyeing process, part of the dyes used to color textile materials are not fixed into the substrate and are discharged into wastewater as residual dyes. In this study, a heterogeneous photocatalytic process combined with microfiltration has been investigated for the removal of C.I. Disperse Red 73 from synthetic textile effluents. The titanium dioxide (TiO2) Aeroxide P25 was selected as photocatalyst. The photocatalytic treatment achieved between 60% and 90% of dye degradation and up to 98% chemical oxygen demand (COD) removal. The influence of different parameters on photocatalytic degradation was studied: pH, initial photocatalyst loading, and dye concentration. The best conditions for dye degradation were pH 4, an initial dye concentration of 50 mg·L−1, and a TiO2 loading of 2 g·L−1. The photocatalytic membrane treatment provided a high quality permeate, which can be reused.