In this article, polylactic acid-based composites reinforced with 5% of polyethylene, iron, and magnesium powders were prepared by extrusion and compressed under the pressure of about 10 MPa and characterized. These composites were mechanically, thermally, and morphologically evaluated. It was found, compared to the pure polylactic acid (PLA), an improvement in tensile strength (both σ and YS0.2) was obtained for the composite with the iron powder addition, while the magnesium powder slightly improved the ductility of the composite material (from 2.0 to 2.5%). Degradation studies of these composites in the 0.9% saline solution over a period of 180 days revealed changes in the pH of the solution from acidic to alkaline, in all samples. The most varied mass loss was observed in the case of the PLA-5%Mg sample, where initially the sample mass increased (first 30 days) then decreased, and after 120 days, the mass increased again. In the context of degradation phenomenon of the tested materials, it turns out that the most stable is the PLA composite with the Fe addition (PLA-5%Fe), with highest tensile strength and hardness.
Additive manufacturing and 3D printing methods based on the extrusion of material have become very popular in recent years. There are many methods of printing ceramics, but the direct extrusion method gives the largest range of sizes of printed objects and enables scaling of processes also in large-scale applications. Additionally, the application of this method to ceramic materials is of particular importance due to its low cost, ease of use, and high material utilization. The paper presents the most important literature reports on ceramics printed by direct extrusion. The review includes articles written in English and published between 2017 and 2022. The aim of this literature review was to present the main groups of ceramic materials produced by extrusion-based 3D printing.
In this study, the influence of TiO2 pigment filler modified with spherosilicate derivatives on the processes and thermomechanical properties of composites based on PLA was investigated. Rheological tests (MFR) were carried out, on the basis of which it was found that the addition of organosilicon compounds has a plasticizing effect on the polymer-filler systems. TGA and DSC analysis were performed. The analysis of the contact angle showed that 1.5% of the additives had an influence on the superhydrophobic properties of TiO2 (above 135°), and a slight improvement of this parameter was also observed for composites containing the modified pigment. Microscopic analysis and mechanical tests (tensile strength, impact strength and flexural strength tests) were carried out as well. It has been observed that the addition of certain derivatives adversely affects the dispersion of the filler, thus a slight improvement in mechanical properties is observed. For modifiers that do not affect filler agglomeration, a plasticizing effect on the composite is observed.
Hot-melt adhesives (HMAs) are thermoplastic materials that can bond various substrates by solidifying rapidly upon cooling from the molten state, and their modification with organosilicon compounds can result in crosslinking behavior, characteristic of gels. Organosilicon compounds are hybrid molecules that have both inorganic and organic components and can enhance the properties and performance of HMAs. The gel aspect of HMA with and without organosilicon modifiers can be considered in organosilicon-modified systems, the modifiers are often either sol–gel condensation products or their mechanism of action on the adherent surface can be considered of sol–gel type. The purpose of this manuscript is to present the current state of the art on the formulation, characterization, and application of HMAs and optimize their performance with organosilicon compounds for application in various industries such as automotive, construction, and photovoltaics. This review covers articles published within the period of 2018–2022. The article is divided into sections, in which information about hot-melt adhesives is described at the beginning. The following part of the presented review focuses on the composition of hot-melt adhesives, which takes into account the use of organosilicon compounds. The last part of this review outlines the future trends in hot-melt adhesives.
Structural bioinspiration in modern material science and biomimetics represents an actual trend that was originally based on the bioarchitectural diversity of invertebrate skeletons, specifically, honeycomb constructs of natural origin, which have been in humanities focus since ancient times. We conducted a study on the principles of bioarchitecture regarding the unique biosilica-based honeycomb-like skeleton of the deep-sea glass sponge Aphrocallistes beatrix. Experimental data show, with compelling evidence, the location of actin filaments within honeycomb-formed hierarchical siliceous walls. Principles of the unique hierarchical organization of such formations are discussed. Inspired by poriferan honeycomb biosilica, we designed diverse models, including 3D printing, using PLA-, resin-, and synthetic-glass-prepared corresponding microtomography-based 3D reconstruction.
An influence of the powder metallurgy route on the phase structure, mechanical properties, and corrosion resistance of Fe–18%Cr–12%Mn–N nickel-free austenitic stainless steel as a potential material for medical applications were studied. The powder was mechanically alloyed in a high purity nitrogen atmosphere for 90 h followed by Hot Isostatic Pressing at 1150 °C (1423 K) and heat treatment at 1175 °C (1423 K) for 1 h in a vacuum with furnace cooling and water quenching. More than 96% of theoretical density was obtained for the samples after Hot Isostatic Pressing that had a direct influence on the tensile strength of the tested samples (Ultimate Tensile Strength is 935 MPa) with the total elongation of 0.5%. Heat treatment did not affect the tensile strength of the tested material, however, an elongation was improved by up to 3.5%. Corrosion properties of the tested austenitic stainless steel in various stages of the manufacturing process were evaluated applying the anodic polarization measurements and compared with the austenitic 316LV stainless steel. In general, the heat treatment applied after Hot Isostatic Pressing improved the corrosion resistance. The Hot Isostatic Pressing sample shows dissolution, while heat treatment causes a passivity range, the noblest corrosion potential, and lower current density of this sample.