A distributed vibration sensing (DVS) system based on phase-sensitive optical time domain reflectometry ($\phi$-OTDR) and distributed feedback interferometer (DFI) with broadband frequency response and high spatial resolution has been proposed and demonstrated. A couple of narrow line-width lasers (NLL) with different wavelengths were used to form the light source, which were consistent with two channels of dense wavelength division multiplexer (DWDM). Both functions of $\phi$-OTDR and DFI could work synchronously without influence between each other. The characteristic of broadband frequency disturbance event could be fully captured and identified by the DFI, while the corresponding location could be determined by the $\phi$-OTDR scheme. Unlike ordinary interferometer, the proposed DFI scheme could make single-end monitoring without the installation of extra accessories. Furthermore, broadband frequency response range and precise locating of the disturbance event could be achieved at the same time. Experimental results have shown that spatial resolution of 10m and frequency response up to 1 MHz has been obtained over 2.16km sensing fiber, which have proved the validity of the proposed method.
Aiming at the problems of large background noise of acoustic signals collected by distributed fiber acoustic sensor (DAS) system and unsatisfactory noise filtering effect of conventional filtering methods, in the study, an improved wavelet denoising scheme based on robust principal component analysis (RPCA) is proposed. The acoustic signal collected by DAS is firstly separated by RPCa algorithm, and then the separated noisy signal is denoised by combining the improved wavelet threshold algorithm with low-pass filter. The test results show that the proposed scheme can improve the signal-to-noise ratio (SNR) by 12~22dB, and the perceptual evaluation of speech quality (PESQ) and correlation coefficient (CC) by 0.6~0.9 and 0.44~0.68 respectively, which can effectively improve the acoustic signal quality. The proposed scheme can accurately restore the acoustic signals in noisy environment, which is of great significance in the fields of acoustic communication, recognition and military reconnaissance.
15 January 2021 in Journal of Mechanical Science and Technology
Accurately reconstructing the strain field within stiffened ship panels is crucial for effective structural health monitoring. This study presents a groundbreaking approach to strain field reconstruction in such panels, utilizing optical fiber sensors in conjunction with the strain function-inverse finite element method (SF-iFEM). A novel technique for solving nodal strain vectors, based on the element strain function, has been devised to improve the accuracy of strain reconstruction using the inverse finite element method (iFEM), addressing the limitations associated with traditional nodal displacement vector solutions. Moreover, the proposed method for determining the equivalent neutral layer of stiffened ship panels not only reduces the number of elements effectively but also establishes a strain function between the inner and outer surfaces of the structure. Using this function, a layout scheme for optical fiber sensors on the inner side of ship stiffened panels is provided, overcoming the symmetrical arrangement constraints of iFEM for sensor placement on both the inner and outer sides of the structure. The results demonstrate a significant improvement in strain reconstruction accuracy under bending and bending–torsion deformations compared to conventional iFEM. Consequently, the findings of this research will contribute to enhancing the engineering applicability of iFEM in ship structure health monitoring.
In this paper, microelectromechanical systems (MEMS) technology was used to fabricate a novel extrinsic fiber Fabry–Perot (EFFP) strain sensor; this fiber sensor is applied to measure load with higher precision for a small structure. The sensor cavity consists of two Fabry–Perot (FP) cavity mirrors that are processed by surface micromachining and then fused and spliced together by the silicon–glass anode bonding process. The initial cavity length can be strictly controlled, and the excellent parallelism of the two faces of the cavity results in a high interference fineness. Then, the anti-reflection coating process is applied to the sensor to improve the clarity of the interference signal with the cavity, with its wavelength working within the range of the C + L band. Next, the sensor placement is determined by the finite element software Nastran. Experimental results indicate that the sensor exhibits a good linear response (99.77%) to load changes and a high repeatability. Considering the strain transfer coefficient, the sensitivity for the tested structure load is as high as 35.6 pm/N. Due to the miniaturization, repeatability, and easy-to-batch production, the proposed sensor can be used as a reliable and practical force sensor.