Florina Ionescu

Dr. Florina Ionescu

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2019 in Materials
Verified
Journal Article
Open access
PDF file
Florina IonescuFlorina Ionescu
Florina Ionescu
Lucien ReclaruLucien Reclaru
Lucien Reclaru
Lavinia Cosmina ArdeleanLavinia Cosmina Ardelean
Lavinia Cosmina Ardelean
ABAndreas Blatter
Andreas Blatter
The evaluation of the biological safety and degradation of materials is quite important for risk assessment in various biomedical applications. In this study, two procedures were followed to characterize the corrosion resistance of different Ti-based alloys. The first one consisted of performing specific electrochemical tests (open circuit potential, linear resistance polarization, Tafel plots, potentiodynamic polarization) in order to highlight their behavior to the general and localized corrosion. The static and dynamic fatigue cycles combined with crevice corrosion conducted on a new prototype have completed the study. The second procedure followed was a cations extraction investigation (by inductively coupled plasma mass spectrometry) in order to verify the ionic permeability of the oxides layers formed on the surfaces. Optical and scanning electron microscopy were used for surface analysis. It was noticed that in these two electrolytes, the bulk Ti-based alloys presented an almost similar general corrosion behavior. The small differences of behavior for Ti6Al4V scaffolds were correlated to the surface oxidation and roughness (owing to the selective laser melting process). The Ti alloys presented no traces of localized corrosion at the end of the test. The fatigue cycles revealed that a strong and adhesive oxides film was formed during the static cycles (difficult to remove even during the depassivation steps). The concentration of cations released was at the detection limit, revealing very good passivation films, in adequacy with the all the other results.

30 March 2024 in Coatings
Verified
Journal Article
Open access
PDF file
Lucien ReclaruLucien Reclaru
Lucien Reclaru
Florina IonescuFlorina Ionescu
Florina Ionescu
FDFrederic Diologent
Frederic Diologent
Watchmaking manufacturers obtain their bracelet links from machining drawn metal profiles. But, today, there is another process that represents an alternative to manufacture them: metal injection molding using metal powders (MIM technology). This process is less expensive than the machining of drawn metal profiles. The aim of this study was to evaluate the corrosion behavior and the nickel cation release of two stainless steel alloys: 316L MIM and 904L MIM. The general corrosion behavior was evaluated by the rotating electrode technique; the galvanic corrosion measurements were conducted with a 316L AISI bulk coupling partner. The pitting corrosion behavior was evaluated in FeCl3 0.5 M media (according to ASTM G48-11). For comparison, a complementary study was conducted on 316L and 904L bulk alloys. The Ni cation release tests were conducted on 316L and 904L MIM and bulk samples according to EN 1811. Different electrochemical parameters were measured and calculated (open circuit potential, polarization resistance, corrosion current and Tafel slopes, coulometric analysis). Generally, if MIM steels are compared with conventional steels, their corrosion resistance behavior is inferior. In the couplings studied, the galvanic currents generated are very important. The shape of the curves also reveals the presence of localized corrosion phenomena. According to tests in ferric chloride, MIM steels were noted to have inferior behavior compared to conventional steels. MIM type 904L steels are comparable in behavior to conventional type 316L steels. The quantities of nickel released according to EN 1811 were very significant (2 mg cm−2 week−1 up to 24 mg cm−2 week−1) and did not meet the requirements of the European directive (0.5 µg cm−2 week−1). In conclusion, conventional steels studied under the same experimental conditions revealed a better behavior compared to MIM steels independently of the phenomenological parameters chosen.

17 May 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Lucien ReclaruLucien Reclaru
Lucien Reclaru
Cosmin Mihai CotrutCosmin Mihai Cotrut
Cosmin Mihai Cotrut
Diana Maria VranceanuDiana Maria Vranceanu
Diana Maria Vranceanu
Florina IonescuFlorina Ionescu
Florina Ionescu
Today, laws protecting the population at the global level aim to minimize the induction risk of allergies to type IV contact dermatitis. In the European population, the prevalence of nickel allergy is at 10%–15% of adult females and 1%–3% of adult males. A total of 30% of nickel-sensitive people in the general population develop hand eczema. This study concerns the possibility of assembling a bottom of nickel-free austenitic steel (Panacea®) in a watch case middle made of a grade of austenitic steels, steel 316L (DIN 1.44359), to avoid the risks of Ni release and to develop a galvanic pile between these two dissimilar materials. Two types of methods were used: direct measurements and prediction techniques (mixed potentials theory). For the degradation of thbottom-middle watch assembly, Nielsen–Tuccillo tests were performed, and Ni release measurements according to EN 1811 completed the study. All direct electrochemical investigations and galvanic current prediction measurements show low current values of 40–400 nA. Measurements of nickel release of Panacea® and 316L reveal small quantities of nickel, much lower than the 0.5 µg/cm2 per week that the European legislation enforces. The nickel-free steel Panacea® in the work hardening conditions 280, 427, and 510 HV0.1s were also studied. The cation extractions reveal the large quantities released from Cr, Mo, Mn, and Fe, so there is a risk of toxicity in contact with the skin.