Due to the high-porosity structure, the low thermal transport property of graphene foam (GF) is expected. However, the interconnected skeleton can still act as excellent thermal conductor branches if phonon scattering is not severely affected in the structure of graphene flakes. Such a property has not been validated experimentally due to the difficulty in sample manipulation and the fragility of the structure. In this work, we report the characterization results of thermal properties of the free-standing skeleton in GF. Three individual skeleton samples from one GF piece are prepared under the same condition. The thermal diffusivity of GF skeletons is characterized in the range of 3.26–3.48 × 10−4 m2/s, and the thermal conductivity is determined to be 520–555 W/(m K), which is two orders of magnitude larger than the value of bulk GF. These high thermal conductivity values originate from the intrinsic thermal property of graphene, while the contact interfaces, wrinkled structures, and defects induced in the synthesis process do not affect the phonon transport property significantly, which proves that the three-dimensional hierarchical graphene structure can still be implemented in energy-intensive applications.
Numerical calculation of conjugate heat transfer was carried out to study the effect of combined film and swirl cooling at the leading edge of a gas turbine vane with a cooling chamber inside. Two cooling chambers (C1 and C2 cases) were specially designed to generate swirl in the chamber, which could enhance overall cooling effectiveness at the leading edge. A simple cooling chamber (C0 case) was designed as a baseline. The effects of different cooling chambers were studied. Compared with the C0 case, the cooling chamber in the C1 case consists of a front cavity and a back cavity and two cavities are connected by a passage on the pressure side to improve the overall cooling effectiveness of the vane. The area-averaged overall cooling effectiveness of the leading edge ( ) was improved by approximately 57%. Based on the C1 case, the passage along the vane was divided into nine segments in the C2 case to enhance the cooling effectiveness at the leading edge, and was enhanced by 75% compared with that in the C0 case. Additionally, the cooling efficiency on the pressure side was improved significantly by using swirl-cooling chambers. Pressure loss in the C2 and C1 cases was larger than that in the C0 case.
Flow separation and different kinds of stall flows occur under low load conditions for steam turbine last stage blades. In order to delay the flow separation and increase turbine power production, we applied suction side tubercles on steam turbine low-pressure last stage blades in the present study. The amplitude, wavelength, position, and thickness were considered as our design variables. We used the orthogonal test method (OTM) to generate modified blades with different tubercle variables that were then numerically simulated by a three-dimensional computational fluid dynamics (CFD) analysis. The blade axial torque of the nine modified tests was compared with the original blade. The results showed that the application of bionic tubercles on the suction side of the steam turbine blade is a promising solution to improve the blade axial torque for all modified tests with a maximum increase of 33.32% due to the turbulent vortices generated by bionic tubercles.
The turbine inlet temperature is one of the most critical parameter that determines the thermal efficiency and thrust-weight ratio of the gas turbine. However, the higher gas turbine inlet temperature significantly increases the thermal stress on the blade, which necessitates effective cooling strategy to reduce the blade temperature. In this study, a united blade cooling strategy was developed by adopting a two-pass ribbed cooling channel with wavy tape for the reason that ribs are near-wall turbulence promoters while the wavy tape is core-region promoter with relatively lower pressure-drop penalty. Ribs and wavy tape may complement each other in the cooling channel. The synergistic effect of the combined near-wall and core-region heat transfer promoter was numerically studied for Reynolds numbers from 6000 to 30000. Two key geometrical factors, namely rib to wave crest phase shift and relative wave amplitude, have significant effect on the thermal performance. The results demonstrate that wavy tape with different phase shift configurations can eliminate the lower heat transfer areas and produce more uniform heat transfer. The 0? phase shift achieved best overall thermal performance, which provided 1.07-1.08 times the flat tape heat transfer enhancement with 1.09-1.11 times the pressure drop penalty. The better heat performance is due to the secondary flow induced by wavy tape, which enhances the fluid mixing between near-wall and core-region.
27 May 2023 in International Journal of Thermal Sciences