The aqueducts built by the ancient Romans are among the most impressive evidence of their engineering skills. The water inside the aqueducts was transported for kilometers, exploiting only the slight but constant differences in altitude throughout the route. To keep the differences in height constant, the aqueducts could proceed underground or aboveground on well-known arched structures that supported lead, ceramic or stone pipes. In order to reconstruct the characteristics of these structures, it is necessary to carry out an accurate survey of the orthometric heights, and therefore the most suitable technology is geometric levelling. In this case, however, it is not applicable, and therefore here we propose an alternative methodology. The final goal of this work was to estimate the flow of some sectors of these aqueducts preserved in the area south of the city of Rome. This has two main purposes: The first is to reconstruct the flow rate of these aqueducts for historical studies; the second is to check how much the orthometric heights have changed over the centuries, in order to reconstruct the movements from a geophysical and geodynamic point of view. The latter analysis will be developed in a following phase of this research. For this purpose, a high-precision geomatic survey was carried out in the area under study, partly retracing a survey already carried out in 1917 whose purpose and methodologies are not known. The area has been affected by a gradual subsidence over centuries, including since 1917. The observed sections of the aqueducts showed average inclinations, slightly lower than the 2 per thousand that is reported in the literature for similar aqueducts. The measurements carried out allowed the flow rate of the two specific aqueducts to be estimated more accurately, both as they were originally and in the presence of deposits that have accumulated during the years of use of the aqueducts. The reconstruction of the initial geometry will later be used as a reference to estimate how much the geodynamic deformations of the area have deformed the aqueducts themselves.
23 February 2018 in International Journal of Earth Sciences
Shell beds represent a useful source of information on various physical processes that cause the depositional condition. We present an automated method to calculate the 3D orientations of a large number of elongate and platy objects (fossilized oyster shells) on a sedimentary bedding plane, developed to support the interpretation of possible depositional patterns, imbrications, or impact of local faults. The study focusses on more than 1900 fossil oyster shells exposed in a densely packed Miocene shell bed. 3D data were acquired by terrestrial laser scanning on an area of 459 m2 with a resolution of 1 mm. Bivalve shells were manually defined as 3D-point clouds of a digital surface model and stored in an ArcGIS database. An individual shell coordinate system (ISCS) was virtually embedded into each shell and its orientation was determined relative to the coordinate system of the entire, tectonically tilted shell bed. Orientation is described by the rotation angles roll, pitch, and yaw in a Cartesian coordinate system. This method allows an efficient measurement and analysis of the orientation of thousands of specimens and is a major advantage compared to the traditional 2D approach, which measures only the azimuth (yaw) angles. The resulting data can variously be utilized for taphonomic analyses and the reconstruction of prevailing hydrodynamic regimes and depositional environments. For the first time, the influence of possible post-sedimentary vertical displacements can be quantified with high accuracy. Here, the effect of nearby fault lines—present in the reef—was tested on strongly tilted oyster shells, but it was found out that the fault lines did not have a statistically significant effect on the large tilt angles. Aside from the high reproducibility, a further advantage of the method is its non-destructive nature, which is especially suitable for geoparks and protected sites such as the studied shell bed.
This paper introduces a technique for modeling the gravity potential using a low-degree Taylor series expansion, specifically of three or four degrees and demonstrates its practical application. The coefficients for this gravity model are the derivatives of the gravity potential at a specified point. The coefficients are determined through Von Eötvös’ torsion balance measurements conducted on the ice sheet of Lake Balaton in Hungary, by minimizing the squares of the difference between the nearby measured (by torsion balance) and calculated second derivatives of gravity potential. The model is applicable over an area spanning several kilometers, encompassing multiple torsion balance measurements, and thus provides broader coverage compared to a strictly local model, thereby justifying its classification as a sub-regional model. The resulting gravity potential field is presented on two types of map, similarly to Eötvös’ work. The derived model characterizes the gravitational potential for the region where measurements were taken, yet it behaves unexpectedly and generates artifacts beyond this measurement area. Earlier geoid models for this region included torsion balance data; in contrast, our results provide a more detailed gravity potential model over a more confined area.
This report covers work on grant FG02-86ER60485 and consists of two parts: progress for the period 9/1/89--5/15/90 and the plan for the remaining period 5/16/90--8/31/90. The project includes two tasks: atmospheric radiation and improvement of climate models to evaluate the climatic effects of radiation changes. 2 refs., 3 figs.