Longfei Xiao

Longfei Xiao


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
XSXun Sun
Xun Sun
LXLongfei Xiao
Longfei Xiao
CLChongbiao Luan
Chongbiao Luan
ZFZhuoyun Feng
Zhuoyun Feng
HSHuiru Sha
Huiru Sha
XXXiangang Xu
Xiangang Xu
Silicon carbide (SiC) is a wide-bandgap semiconductor suitable for high-power high-voltage devices, especially the feasibility and superiority of SiC photoconductive semiconductor in microwave generation have been demonstrated via linear operating mode. Here, the photoconductive semiconductor switch (PCSS) with a channel length of 0.5 mm is fabricated as planar structures on high-purity semi-insulating 4H-SiC. The experimental results show that the voltage transmission of the elliptic morphology laser incident from the rear is larger than the circular counterpart, which is consistent with the formula calculation and the simulations of the current density distribution of a 2-D cross section. Upon the elliptic incident laser centered at ∼355 nm, the peak voltage transmission efficiency of SiC PCSS is 99.5% at the biased voltage of ∼2220 V. In addition, the output voltage waveform is observed with a half-height width of roughly 1.6 ns and rise time of less than 300 ps as well as the minimum on -state resistance of approximately 0.3 Ω at this moment.

19 December 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
ZFZhuoyun Feng
Zhuoyun Feng
CLChongbiao Luan
Chongbiao Luan
LXLongfei Xiao
Longfei Xiao
YLYangfan Li
Yangfan Li
HSHuiru Sha
Huiru Sha
HLHongtao Li
Hongtao Li
Radial lateral structure photoconductive switches are fabricated in this work via vanadium-doped 4H-SiC and high-purity 4H-SiC materials. The switches are triggered by 355- and 532-nm laser, and the performance of the switch is compared in the applied voltage range of 1–10 kV and laser energy range of 0.3–14 mJ. The experimental results show that the conduction current of the laser incident from the rear is larger. Simulations of the current density distribution of a 2-D cross section of the photoconductive switch provide theoretical support for this phenomenon. Additionally, the conduction current of the high-purity material is found to be higher than that of the vanadium-doped material under the same conditions.

7 April 2021 in Applied Optics
Verified
Journal Article
Closed access
ZFZhuoyun Feng
Zhuoyun Feng
LXLongfei Xiao
Longfei Xiao
CLChongbian Luan
Chongbian Luan
YLYangfan Li
Yangfan Li
HSHuiru Sha
Huiru Sha
XXXiangang Xu
Xiangang Xu
Semi-insulating (SI) SiC photoconductive semiconductor switches were prepared using two compensation mechanisms: namely vanadium dopants compensation (4H- and 6H-SiC) and deep level defect compensation (4H-SiC). The bias voltage and current of the high-purity (HP) SI 4H-SiC photoconductive semiconductor switch (PCSS) with a channel length of 1 mm reached 24 kV and 364 A, respectively, and the minimum on-state resistance of approximately 1 Ω was triggered by laser illumination at a wavelength of 355 nm. The experimental results show that, in this case, the on-state characteristics of HP 4H-SiC PCSS are superior to those of the vanadium-doped(VD) 4H and 6H-SiC PCSS devices. HP 4H-SiC PCSS shows remarkable waveform consistency. Unlike for VD 4H and 6H-SiC PCSS, the current waveform of HP 4H-SiC PCSS exhibits a tailing phenomenon due to its longer carrier lifetime.

3 November 2019 in Sensors
Verified
Journal Article
Open access
PDF file
RWRongkun Wang
Rongkun Wang
Xuejian XieXuejian Xie
Xuejian Xie
Xu XiangangXu Xiangang
Xu Xiangang
XCXiufang Chen
Xiufang Chen
LXLongfei Xiao
Longfei Xiao
Silicon-diaphragm-based fiber-optic Fabry–Perot sensors with different intracavity pressures were fabricated by anodic bonding and microelectromechanical techniques. The thermal stress and thermal expansion of the Fabry–Perot (FP) sensor caused by high-temperature bonding and temperature change were simulated by finite-element analysis. The calculated thermal stress is largest in the center and edge regions of the resonance cavity, reaching from 2 to 6 MPa. The reflection spectra and temperature sensitivity of the sensors were simulated by using a two-dimensional wave-optic model in Comsol. Theoretical calculations were also made for the FP cavity without considering silicon-diaphragm deformation and thermal stress. Four sensors with intracavity pressures of 0.01, 0.03, 0.04, and 0.05 MPa were tested at low temperatures, showing a high degree of consistency with the simulation results rather than theoretical calculation, especially for high intracavity pressure. This method is expected to aid the analysis of thermal stress generated during the bonding process and to facilitate better design and control of the temperature sensitivity of the sensor.

12 November 2024 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
YLYangfan Li
Yangfan Li
LXLongfei Xiao
Longfei Xiao
CLChongbiao Luan
Chongbiao Luan
XSXun Sun
Xun Sun
HSHuiru Sha
Huiru Sha
XXXiangang Xu
Xiangang Xu
To minimize the rise time and full-width at half-maximum (FWHM) of the output waveform, we have designed and fabricated a novel integrated device based on semi-insulated silicon carbide (SiC) material, which we call cPCSS device, whose structure includes a photoconductive semiconductor switch (PCSS) and a charging capacitor. Test results indicate that, owing to optimized circuit connections and a simplified electrical length in cPCSS, the parasitic capacitance and inductance in the test circuit are decreased. Consequently, the cPCSS device exhibits faster signal while maintaining basically equal conductivity. At the incident laser energy (10 $\mu$ J), cPCSS obtains the output signal with the fastest rise time of 122 ps (10%–90%) and FWHM of 375 ps. In addition, the cPCSS device can maintain a peak output voltage exceeding 10 kV and continuously output signals for more than 180 000 times without any faults.

5 December 2023 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
YQYan Qin
Yan Qin
CLChongbiao Luan
Chongbiao Luan
LXLongfei Xiao
Longfei Xiao
YLYangfan Li
Yangfan Li
ZFZhuoyun Feng
Zhuoyun Feng
HLHongtao Li
Hongtao Li
A lateral PCSS with a sinking-electrode structure was proposed in this work. Silvaco TCAD was used to simulate the electric field distribution of the switches with different groove etching depths. The simulation results show that the internal peak electric field and external quantum efficiency (EQE) of a sinking-electrode PCSS with a 1 mm gap were 61% and 270% of the conventional switch, respectively. A 355 nm YAG laser with a dc high voltage source was also used to test the sinking-electrode switches with different electrode gaps. The sinking-electrode switch with a small electrode gap achieved the same breakdown voltage value with higher current and quantum efficiency compared to the conventional switch with a large gap. The acquired experimental results were in good agreement with the simulated outcomes, and the good ON-state performance confirmed the improved photoelectric conversion efficiency and high voltage resistance of the introduced sinking-electrode PCSSs.