The aim of this study was to identify and analyze the fatigue fracture characteristics of dissimilar Al 6061 to Cu (UNS C11000) lap joints made with ultrafast electromagnetic pulse welding (EMPW) via fractography, stress analysis and finite element simulation. It was observed that EMPW generated an annular (or ring-shaped) bonding area, with weld zones and a central non-weld zone when viewed from the cross section. Two types of failure modes occurred in relation to the cyclic loading levels: base metal fracture or transverse through-thickness (TTT) crack growth at a higher loading level, and joint interfacial failure at a lower loading level. In the interfacial failure, fatigue crack initiated from the outer edge of annular welding area, and propagated to form an approximate elliptical boundary. Fatigue crack propagation was characterized by fatigue striations existing in discrete areas on the fracture surface. This was attributed to a coupled role of shear and normal stresses present in a tensile lap shear sample due to the bending moment caused by the inherent misalignment. The final rapid fracture started from elliptical boundary with elongated shear dimples. Both theoretical stress analysis and finite element model revealed the maximum stress and stress concentration along the outer edge, where fatigue crack initiation occurred.

The aim of this study was to characterize detailed microstructural changes and bonding characteristics and identify the formation mechanism of collision surface of Al6061–Q355 steel dissimilar welded joints via electromagnetic pulse welding (EMPW). The collision surface was observed to consist of five zones from the center to the outside. The central non-weld zone exhibited a concave and convex morphology. The welding-affected zone mainly included melting features and porous structures, representing a porous joining. The secondary weld zone presented an obvious mechanical joining characterized by shear plateaus with stripes. The primary weld zone characterized by dimples with cavity features suggested the formation of diffusion or metallurgical bonding. The impact-affected zone denoted an invalid interfacial bonding due to discontinuous spot impact. During EMPW, the impact energy and pressure affected the changes of normal velocity and tangential velocity, and in turn, influenced the interfacial deformation behavior and bonding characteristics, including the formation of micropores which continued to grow into homogeneous or uneven porous structures via cavitation, surface tension, and depressurization, along with the effect of trapped air.

Facing the environment problems, the improvement on the efficiency of the construction machinery is highly demanded, meanwhile, large energy wasted in hydraulic slewing systems, reaching the desired speed slowly and vibration in braking are widespread. In this paper, a closed-loop control swing system (CCSS) is proposed. In this system, bidirectional variable pump controls the change of oil flow by programmed software algorithm, instead of pilot actuated reversing valve, which significantly improves the efficiency of hydraulic circuit. Based on the model structures, we develop a hydraulic swing prototype and verify the advantages of our design means of theoretical calculation and simulation. It verifies that CCSS and based on accumulator slewing system(BASS) can respectively save 875.5 KJ and 347.2 KJ more than OCSS with operational weight of 100 tons grasp steel machine, which can support theoretical basis for energy conservation and environmental protection to study the new type of engineering machinery.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.