Di Wang

Prof. Dr. Di Wang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
HFHoucheng Fang
Houcheng Fang
DWDi Wang
Di Wang
In order to verify the delamination damage occurring in thick-walled composite-overwrapped pressure vessels, firstly, for composite delamination damage, a composite laminate model was established. Model I and model II delamination failure processes of composite structures were simulated and verified based on a tiebreak contact algorithm for different mesh sizes, respectively, and the approximate equivalent results were achieved by correcting the inter-ply strength. Then, for in-plane damage to composite materials, the elastic–plastic process was verified by selecting a progressive damage model, with quasistatic nonlinear tensile shear of sample specimens as an example. Further, under the purpose of generality and simplicity, the location of the first occurrence of delamination failure was simulated and analyzed with the tiebreak contact algorithm and a reasonable mesh size, using quasistatic loading of a thick composite-overwrapped pressure vessel cylindrical section as an example. The results showed that delamination occurred at approximately the center, which is in general agreement with the experimentally observed phenomenon. On this basis, the locations of the first significant delamination phenomena in composite-overwrapped vessels under three different ratios of plus or minus 45-degree layup angles were predicted. Finally, the differences in structural strength between the single laying methods and the combined laying method were compared. The results showed that the ratio of 50% had a higher modulus value than a pure 0° ply, but too large a ratio was detrimental to the improvement of structural properties.

17 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
DWDi Wang
Di Wang
FMFangping Ma
Fangping Ma
HCHao Chen
Hao Chen
Hydrogen-assisted cracking is one of the most dominant failure modes in metal hydrogen-facing materials. Therefore, the hydrogen-assisted cracking mechanism has been a hot topic for a long time. To date, there is very little published research on numerical methods to describe hydrogen-assisted cracking. This paper presents a new method for the description of hydrogen embrittlement crack growth: an explicit phase-field formulation, which is based on the phase-field description of cracks, Fick’s mass diffusion law, and the relationship between hydrogen content and fracture surface energy. A novel computational framework is then developed using the self-developed FEM software DYNA-WD. We numerically calculate several typical conditions in the 3-D coordinates to validate the effectiveness of the proposed computational framework. Specifically, we discuss (i) the failure of a square plate in a hydrogenous environment, (ii) the CT specimen failed with the inner hydrogen, (iii) the plate/failed with the corrosives, and (iv) the failure of the disk test. Finally, the relationship between Mises stress, the concentration of hydrogen, the thickness of the disc, and the loading rate is investigated.

Verified
Journal Article
Open access
PDF file
DWDi Wang
Di Wang
JXJinhong Xie
Jinhong Xie
The temperature of an electric vehicle battery system influences its performance and usage life. In order to prolong the lifecycle of power batteries and improve the safety of electric vehicles, this paper designs a liquid cooling and heating device for the battery package. On the device designed, we carry out liquid cooling experiments and preheating experiments. Then, a three-dimensional numerical model for the battery package is built, and its effectiveness is validated by comparing the simulation results with the experimental outcomes in terms of battery surface temperature and temperature difference. Furthermore, we investigate the influences of the liquid flow rate and the inlet temperature on the maximum temperature and temperature difference of batteries by the cooling models and preheating models. Results show that: at the cooling stage, it is able to keep each battery working at an optimal temperature under different discharge conditions by changing the flow and the inlet temperature of liquid; at the heating stage, large flow rates and high inlet temperatures are able to speed up the preheating process, thereby saving time of the drivers.

21 September 2023 in Agriculture
Verified
Journal Article
Open access
PDF file
XJXiaoming Jin
Xiaoming Jin
FMFangping Ma
Fangping Ma
DWDi Wang
Di Wang
ZZZhengtao ZHu
Zhengtao ZHu
In the field of agricultural machinery, various empirical field tests are performed to measure the tillage force for precision tillage. However, the field test performance is costly and time-consuming, and there are many constraints on weather and field soil conditions; the utilization of simulation studies is required to overcome these shortcomings. As a result, the SPH method and the coupled FEM-SPH method are used in this paper to investigate the mouldboard plough–soil interaction. In this paper, the finite element software LS-DYNA was used to build the SPH model and the FEM-SPH coupling model of soil cutting, as well as to investigate the change in cutting resistance during the soil cutting process. The simulation results are compared with those of the experiments, and the curves of the simulation and experiment are in good agreement, which verifies the reliability of the model. The validated simulation model was used to investigate the effects of the cutting speed, depth of cut, inclination angle, and lifting angle of the mouldboard plough on cutting resistance. The simulation studies show that the SPH model takes 5 h and 2 min to compute, while the FEM-SPH coupled model takes 38 min; obviously, the computational efficiency of the FEM-SPH coupled model is higher. The relative errors between the SPH model and the experiment are 2.17% and 3.65%, respectively. The relative errors between the FEM-SPH coupled model and the experiment are 5.96% and 10.67%, respectively. Obviously, the SPH model has a higher computational accuracy. The average cutting resistances predicted by the SPH model and the FEM-SPH coupled model, respectively, were 349.48 N and 306.25 N; these resistances are useful for precision tillage. The cutting resistance increases with the increase in cutting speed and is quadratic; the cutting resistance increases with the increase in cutting depth and is quadratic; the horizontal cutting resistance and the combined cutting resistance increase with the increase in inclination angle, while the vertical cutting resistance remains essentially constant with the increase in inclination angle; the horizontal cutting resistance and combined cutting resistance increase as the lifting angle increases, while the vertical cutting resistance decreases as the lifting angle increases.

18 June 2023 in Machines
Verified
Journal Article
Open access
PDF file
DWDi Wang
Di Wang
HWHui Wang
Hui Wang
YXYan Xu
Yan Xu
JZJianping ZHOU
Jianping ZHOU
XSXinyu Sui
Xinyu Sui
Wheeled machines, such as agricultural tractors, snowplows, and wheeled mobile robots, usually work on icy or snow-covered roads. Therefore, it is very important to study the driving and slip resistance of the tires of these machines. In this paper, we investigate the driving behavior of tires on snow-covered terrain by means of numerical simulations. A high-fidelity snow-covered road model is established, and smoothed particle hydrodynamics (SPH) and the finite element method (FEM) are employed to account for the behaviors of the snow layers and the pavement, respectively. We use the node-to-surface algorithm for the contact interactions between the snow and the pavement. The SPH parameters for the snow are calibrated by means of a triaxial compression experiment. A simplified tire model is established as well, using the FEM, and the effectiveness of the model is demonstrated via comparisons with the experimental data in terms of stiffness. Finally, the tire driving performance on the snow-covered road is simulated, and the influence of the tire surface configuration, external load, inflation pressure, and snowpack compression on the tire traction behaviors is systematically investigated.

26 March 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
FMFangping Ma
Fangping Ma
ZZZhengtao ZHu
Zhengtao ZHu
DWDi Wang
Di Wang
XJXiaoming Jin
Xiaoming Jin
Aircraft icing has historically been a critical cause of airplane crashes. The electro-impulse de-icing system has a wide range of applications in aircraft de-icing due to its lightweight design, low energy consumption, high efficiency, and other advantages. However, there has been little study into accurate wing electric-impulse de-icing simulation methods and the parameters impacting de-icing efficacy. Based on the damage mechanics principle and considering the influence mechanisms of interface debonding and ice fracture on ice shedding, this paper establishes a more accurate numerical model of wing electric-impulse de-icing using the Cohesive Zone Model (CZM). It simulates the process of electric-impulse de-icing at the leading edge of the NACA 0012 wing. The numerical results are compared to the experimental results, revealing that the constructed wing electro-impulse de-icing numerical model is superior. Lastly, the effects of varying ice–skin interface shear adhesion strengths, doubler loading positions, and impulse sequences on de-icing effectiveness were studied. The de-icing rate is a quantitative description of the electro-impulse’s de-icing action, defined in the numerical model as the ratio of cohesive element deletions to the total elements at the ice–skin interface. The findings reveal that varying shear adhesion strengths at the ice–skin interface significantly impact the de-icing effect. The de-icing rate steadily falls with increasing shear adhesion strength, from 66% to 56%. When two, four, and seven impulses were applied to doubler two, the de-icing rates were 59%, 71%, and 71%, respectively, significantly increasing the de-icing efficiency compared to when impulses were applied to doubler one. Doubler one and two impulse responses are overlaid differently depending on the impulse sequences, resulting in varying de-icing rates. When the impulse sequence is 20 ms, the superposition results are optimal, and the de-icing rate reaches 100%. These studies can guide the development and implementation of a wing electric-impulse de-icing system.