In this paper, the complex two-phase flow during oil-jet impingement on a rotating spur gear is investigated using the meshless smoothed particle hydrodynamics (SPH) method. On the basis of a two-dimensional setup, a comparison of single-phase SPH to multiphase SPH simulations and the application of the volume of fluid method is drawn. The results of the different approaches are compared regarding the predicted flow phenomenology and computational effort. It is shown that the application of single-phase SPH is justified and that this approach is superior in computational time, enabling faster simulations. In the next step, a three-dimensional single-phase SPH setup is exploited to predict the flow phenomena during the impingement of an oil-jet on a spur gear for three different jet inclination angles. The oil’s flow phenomenology is described and the obtained resistance torque is presented. Thereby, a significant effect of the inclination angle on the oil spreading and splashing process as well as the resistance torque is identified.
Labyrinth seals are a state-of-the-art sealing technology to prevent and control leakage flows at rotor–stator interfaces in turbomachinery. Higher pressure ratios and the economical use of cooling air require small clearances, which lead to potential rubbing events. The use of honeycomb liners allows for minimal leakage by tolerating rub events to a certain extent. A previous study within an EU project investigated the complex contact conditions of honeycomb liners, with the idealized contact of a seal fin and a single parallel metal foil representing the honeycomb double foil section. In the present work, the results for the slanted foil position are shown and compared to the previous results. The variation of rub velocity, incursion speed, incursion rate, and seal geometry in a test rig allows for the identification of the influence on contact forces, temperatures, and wear. For the slanted position, significantly lower friction temperatures are observed, leading to a higher ratio of abrasive wear. Overall, the rub test results demonstrate strong interactions between the contact forces, friction temperatures, and wear.
This paper discusses the question of heat flux distribution between bristle package and rotor during a rubbing event. A three-dimensional Computational Fluid Dynamics (3D CFD) model of the brush seal test rig installed at the Institute of Thermal Turbomachinery (ITS) was created. The bristle package is modelled as a porous medium with local non-thermal equilibrium. The model is used to numerically recalculate experimentally conducted rub tests on the ITS test rig. The experimentally determined total frictional power loss serves as an input parameter to the numerical calculation. By means of statistical evaluation methods, the ma in influences on the heat flux distribution and the maximum temperature in the frictional contact are determined. The heat conductivity of the rotor material, the heat transfer coefficients at the bristles and the rubbing surface were identified as the dominant factors.
Reducing losses in the secondary air system of gas and steam turbines can significantly increase the efficiency of such machines. Meanwhile, brush seals are a widely used alternative to labyrinth seals. Their most valuable advantage over other sealing concepts is the very small gap between the sealing package and the rotor and thus reduced leakage mass flow. This small gap can be achieved due to the great radial flexibility without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g., an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or manoeuvre forces. Thanks to the flexible structure of the brush seal, the contact forces during a rubbing event are reduced; however, the frictional heat input can still be considerable. Particularly in aircraft engines with their thin and lightweight rotor structures, the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine’s integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. This paper is a contribution to further understand the influence of the geometrical parameters of the brush seal on the heat input and the leakage during the rubbing of the seal on the rotor. In this paper, a total of three seals with varied back plate inner diameter are examined in more detail. The experimental tests were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) under machine-relevant conditions. These are represented by pressure differences of 1 to 7 bar, surface speeds of 30 to 180 m/s and radial interferences of 0.1 to 0.4 mm. For a better interpretation, the results were compared with those obtained at the static test rig of the Institute of Jet Propulsion and Turbomachinery (IFAS) at the Technical University of Braunschweig. The stiffness, the blow-down and the axial behaviour of the seals as a function of the differential pressure can be examined at this test rig. It could be shown that the back plate inner diameter has a decisive influence on the overall operating behaviour of a brush seal.
27 February 2019 in Journal of Engineering for Gas Turbines and Power
Because of the superior sealing characteristics compared to labyrinth seals, brush seals found an increased spread in turbomachinery in recent years. Their outstanding sealing performance results mainly from their flexibility. Thus, a very small gap between the rotor and bristle package can be obtained without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g., an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or maneuver forces. Thanks to the flexible structure of the brush seal the contact forces during a rubbing event are reduced; however, the frictional heat input can still be considerable. Particularly, in aircraft engines with their thin and lightweight rotor structures, the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine's integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. The complex interactions between the geometric parameters of the seal and the heat input and leakage characteristics are not yet fully understood. This paper presents the investigation of the influence of the geometric parameters of a brush seal on the heat input into the rotor and the leakage behavior. Two seals with different packing densities were tested under relevant engine conditions with pressure differences ranging from 1 to 7 bar, relative surface speeds ranging from 30 to 180 m/s, and radial overlaps ranging from 0.1 to 0.4 mm. The transient temperature rise during the rub event was recorded with 24 thermocouples in close proximity to the rub contact embedded in the rotor structure. By comparing the temperature curves with the results of a thermal finite element (FE) analysis of the rotor the heat input into the rotor was calculated iteratively. It could be shown that the packing density has a decisive influence on the overall operating behavior of a brush seal. Furthermore, results for the heat flux distribution between seal and rotor are shown.