Ambitious targets to reduce emissions caused by aviation in the light of an expected ongoing rise of the air transport demand in the future drive the research of propulsion systems with lower CO₂ emissions. Regional hybrid electric aircraft (HEA) powered by conventional gas turbines and battery powered electric motors are investigated to test hybrid propulsion operation strategies. Especially the role of the battery within environmentally friendly concepts with significantly reduced carbon footprint is analyzed. Thus, a new simulation approach for HEA is introduced. The main findings underline the importance of choosing the right power-to-energy-ratio of a battery according to the flight mission. The gravimetric energy and power density of the electric storages determine the technologically feasibility of hybrid concepts. Cost competitive HEA configurations are found, but do not promise the targeted CO₂ emission savings, when the well-to-wheel system is regarded with its actual costs. Sensitivity studies are used to determine external levers that favor the profitability of HEA.

With the growth of aviation traffic and the demand for emission reduction, alternative fuels like the so-called electrofuels could comprise a sustainable solution. Electrofuels are understood as those that use renewable energy for fuel synthesis and that are carbon-neutral with respect to greenhouse gas emission. In this study, five potential electrofuels are discussed with respect to the potential application as aviation fuels, being n-octane, methanol, methane, hydrogen and ammonia, and compared to conventional Jet A-1 fuel. Three important aspects are illuminated. Firstly, the synthesis process of the electrofuel is described with its technological paths, its energy efficiency and the maturity or research need of the production. Secondly, the physico-chemical properties are compared with respect to specific energy, energy density, as well as those properties relevant to the combustion of the fuels, i.e., autoignition delay time, adiabatic flame temperature, laminar flame speed and extinction strain rate. Results show that the physical and combustion properties significantly differ from jet fuel, except for n-octane. The results describe how the different electrofuels perform with respect to important aspects such as fuel and air mass flow rates. In addition, the results help determine mixture properties of the exhaust gas for each electrofuel. Thirdly, a turbine configuration is investigated at a constant operating point to further analyze the drop-in potential of electrofuels in aircraft engines. It is found that electrofuels can generally substitute conventional kerosene-based fuels, but have some downsides in the form of higher structural loads and potentially lower efficiencies. Finally, a preliminary comparative evaluation matrix is developed. It contains specifically those fields for the different proposed electrofuels where special challenges and problematic points are seen that need more research for potential application. Synthetically-produced n-octane is seen as a potential candidate for a future electrofuel where even a drop-in capability is given. For the other fuels, more issues need further research to allow the application as electrofuels in aviation. Specifically interesting could be the combination of hydrogen with ammonia in the far future; however, the research is just at the beginning stage.

Boundary layer ingestion is a promising method to decrease the propulsive power consumption of an aircraft, and therefore the fuel consumption. This leads to a reduced environmental impact and an improved cost-efficiency. To get a better understanding of this method and to estimate its benefits, the modelling of a propulsor located at the upper rear centerbody of a blended wing body aircraft is presented in this paper. A parallel compressor model approach is used to analyse the impact of the ingested low velocity fluid which leads to a non-uniform inflow. The required boundary layer data are generated with an analysis tool for 2D subsonic airfoils. Some parameter variations are conducted with the developed programme to study their impact on the power saving potential. In addition, a simple estimation for the benefit of embedded aeroengines is given. Despite the drawback from fan efficiency due to the inflow distortion, the results show a significant decrease in required propulsive power for boundary layer ingestion in combination with integrated engines.

The Propulsion Test Facility of the TU Braunschweig is capable of investigating future jet engine intakes and fan aerodynamics to a high level of detail. A goal of this facility is the examination of coupled fan-intake-interactions which is not possible in any existing test bench around the world. Before doing research on these interactions, it is important to undergo proper studies of isolated aspirated intakes and fans under varying operating conditions (design and off-design). Therefore comparable result of the well-known LARA nacelle to existing experimental and numerical data has been generated for a first validation purpose. Therefore, comparable studies have been conducted with the LARA nacelle, to that of experimental and numerical investigations performed in the early 1990s at the ONERA F1 wind tunnel (mention reference), in order to generate results for validation. The first results of the validation experiment show differences in peak Mach number between the ONERA F1 and PTF experimental data for identical boundary conditions based on Mach number and crosswind. To investigate this further, a comprehensive numerical study has been carried out. It was inferred that the discrepancy was mainly caused by the Reynolds number effect within the PTF environment and its sensitivity to the inlet flow angle distribution with regard to angle of attack for crosswind. Within the validation test campaign, the experimental investigations showed a separation and reattachment hysteresis, which was identified when crosswind as well as nacelle mass flow had been increased or decreased to set up the different operating points. This phenomenon has still no established theoretical basis for understanding the aerodynamic behaviour. Overall, the applicability of conventional RANS models is shown. Additionally, the sensitivity to the aforementioned boundary conditions and the numerical reproducibility of the hysteresis phenomenon are discussed and compared to new experimental data in detail.

The overall efficiency and operational behavior of aircraft engines are influenced by the surface finish of the airfoils. During operation, the surface roughness significantly increases due to erosion and deposition processes. The aim of this study is to analyze the influence of roughness on the aerodynamics of the low-pressure turbine of a mid-sized high bypass turbofan. In order to gain a better insight into the operational roughness structures, a sample of new, used, cleaned and reworked turbine blades and vanes are measured using the confocal laser scanning microscopy technique. The measurement results show local inhomogeneities. The roughness distributions measured are then converted into their equivalent sand grain roughness $k_{s,eq} $ to permit an evaluation of the impact on aerodynamic losses. The numerical study is performed using the CFD-solver TRACE which was validated before with existing data from Rig experiments. The service-induced roughness structures cause an efficiency drop in the low pressure turbine of $\eta_T = -0.16\%$ compared to new parts. A gas path analysis showed that this results in an increased fuel flow of $\Delta \dot m_f = +0.06\%$ and an exhaust gas temperature rise of $\Delta EGT = +1.2 K $ for fixed engine pressure ratio which is equivalent to roughly 4 percent of the typical EGT margin of a fully refurbished engine. This result stresses the importance of roughness induced loss in low pressure turbines.

Radial turbines used in automotive fuel cell turbochargers operate with humid air. The gas expansion in the turbine causes droplets to form, which then grow through condensation. The associated release of latent heat and decrease in the gaseous mass flow strongly influence the thermodynamics of the turbine. This study aims to investigate these phenomena. For this purpose, the classical nucleation theory and Young’s growth law are integrated into a Euler–Lagrange approach. The main advantages of this approach are the calculation of individual droplet trajectories and a full resolution of the droplet spectrum. The results indicate an onset of nucleation at the blade tip and in the tip gap, followed by nucleation over the entire blade span, depending on the humidity at the turbine inlet. With a saturated turbine inflow, condensation causes the outlet temperature to rise to almost the same level as at the inlet. In addition, condensation losses reduce the efficiency and the latent heat released by condensation leads to significant thermal throttling.