In this paper, we demonstrate the high electrical activity of extended defects found in 3C–SiC heteroepitaxially grown layer on (100) silicon substrates. Cross-sectional scanning transmission electron microscopy analysis was performed to reveal the defects while scanning spreading resistance microscopy aimed to study their electrical behavior. Using this technique, complete layer resistance cartography was done. The electrical activity of the extended defects in 3C–SiC was clearly evidenced. Furthermore, the defect activity was estimated to be higher than that of heavily nitrogen doped (5×1018 cm−3) 3C–SiC layer.
In this paper, we study the electrochemical anodization of n-type heavily doped 4 H-SiC wafers in a HF-based electrolyte without any UV light assistance. We present, in particular, the differences observed between the etching of Si and C faces. In the case of the Si face, the resulting material is mesoporous (diameters in the range of 5 to 50 nm) with an increase of the ‘chevron shaped’ pore density with depth. In the case of the C face, a columnar morphology is observed, and the etch rate is twice greater than for the one for the Si face. We've also observed the evolution of the potential for a fixed applied current density. Finally, some wafer defects induced by polishing are clearly revealed at the sample surfaces even for very short etching times.
A detailed study of the static bending of micro-cantilevers has been performed for structures created from thin 3C-SiC films grown on (100) and (111) oriented silicon substrates. The biaxial stress distribution in the direction of the film normal has been evaluated based on analysis of the deformation profiles of clamped-free 3C-SiC beams of various thicknesses. Surprisingly, the obtained results clearly indicate that for as-grown samples of both studied orientations, the absolute value of the intrinsic stress increases from the interface to the surface of the film. We propose a simple analytical model of a relaxation process that explains in a quantitative way this unexpected phenomenon of stress gradient inversion.
The stress state is a crucial parameter for the design of innovative microelectromechanical systems based on silicon carbide (SiC) material. Hence, mechanical properties of such structures highly depend on the fabrication process. Despite significant progresses in thin-film growth and fabrication process, monitoring the strain of the suspended SiC thin-films is still challenging. However, 3C-SiC membranes on silicon (Si) substrates have been demonstrated, but due to the low quality of the SiC/Si heteroepitaxy, high levels of residual strains were always observed. In order to achieve promising self-standing films with low residual stress, an alternative micromachining technique based on electrochemical etching of high quality homoepitaxy 4H-SiC layers was evaluated. This work is dedicated to the determination of their mechanical properties and more specifically, to the characterization of a 4H-SiC freestanding film with a circular shape. An inverse problem method was implemented, where experimental results obtained from bulge test are fitted with theoretical static load-deflection curves of the stressed membrane. To assess data validity, the dynamic behavior of the membrane was also investigated: Experimentally, by means of laser Doppler vibrometry (LDV) and theoretically, by means of finite element computations. The two methods provided very similar results since one obtained a Young’s modulus of 410 GPa and a residual stress value of 41 MPa from bulge test against 400 GPa and 30 MPa for the LDV analysis. The determined Young’s modulus is in good agreement with literature values. Moreover, residual stress values demonstrate that the fabrication of low-stressed SiC films is achievable thanks to the micromachining process developed.
Cantilevers with resonance frequency ranging from 1 MHz to 100 MHz have been developed for dynamic atomic force microscopy. These sensors are fabricated from 3C-SiC epilayers grown on Si(100) substrates by low pressure chemical vapor deposition. They use an on-chip method both for driving and sensing the displacement of the cantilever. A first gold metallic loop deposited on top of the cantilever is used to drive its oscillation by electrothermal actuation. The sensing of this oscillation is performed by monitoring the resistance of a second Au loop. This metallic piezoresistive detection method has distinct advantages relative to more common semiconductor-based schemes. The optimization, design, fabrication, and characteristics of these cantilevers are discussed.