A phosphor-converted light-emitting diode (LED) solar simulator is an illuminance device that produced irradiance intensity and spectral close to the sunlight. It is determined as spectral mismatch, non-uniformity of irradiance, and temporal instability. This paper has improved the LED solar simulator (LSS) system to have a spectral distribution consistent with the AM1.5G spectrum at 100%. It was developed as a new prototype to have the AAA class spectral characteristics, time instability, and inconsistency according to IEC 60904-9. The results showed that an optimal approach was to use phosphor-converted natural white LED (pc-nWLED), combining a monochromatic near-infrared (NIR) (730, 800, 850, 940, and 1,000 nm) as well as the proposed LSS system capable of generating 1,000 W/m2 irradiation over the test plane of 125×125 mm and operated continuously in a constant temperature LED state for at least 2 hours, therefore suitable for demonstration of solar cell features under standard test condition (STC) in the laboratory.
1 January 2022 in Indonesian Journal of Electrical Engineering and Computer Science
Low-level light therapy (LLLT) uses the light of wavelength between 400–700 nm to treat acne, reduce inflammation, stimulate collagen production, and rejuvenate the facial skin. This study designed and constructed a dual-wavelength LED LLLT device for the facial treatment. The light spectrum, power density, uniformity, stability, and safety of the device were analyzed. The proposed system consisted of an LED array with 415 and 633 nm wavelengths. Human machine interface with embedded system was used to control light intensity and treatment time. The phototherapy device is designed to be curvaceously sized to suit the face shape of Asian people. The results showed that the LLLT device emitted 633±5 nm red and 415±5 nm blue light with a linear adjustable light power density of 0-18.56 mW/cm2 and 0-3.70 mW/cm2, respectively. The spectrum distribution of the red and blue light was relatively constant over 30 minutes of operation. The uniformity and stability of red spectrum were about 89.9% and 95.08% and blue spectrum were 87.6% and 97.08%, respectively. The experimental face’s temperature was below 31.5 . For the future study, the LED phototherapy device will be applied for clinical research in collaboration with dermatologists.Low-level light therapy (LLLT) uses the light of wavelength between 400–700 nm to treat acne, reduce inflammation, stimulate collagen production, and rejuvenate the facial skin. This study designed and constructed a dual-wavelength LED LLLT device for the facial treatment. The light spectrum, power density, uniformity, stability, and safety of the device were analyzed. The proposed system consisted of an LED array with 415 and 633 nm wavelengths. Human machine interface with embedded system was used to control light intensity and treatment time. The phototherapy device is designed to be curvaceously sized to suit the face shape of Asian people. The results showed that the LLLT device emitted 633±5 nm red and 415±5 nm blue light with a linear adjustable light power density of 0-18.56 mW/cm2 and 0-3.70 mW/cm2, respectively. The spectrum distribution of the red and blue light was relatively constant over 30 minutes of operation. The uniformity and stability of red spectrum were about 89.9% and 95.08% and blue spectrum were 87.6% and 97.08%, respectively. The experimental face’s temperature was below 31.5 . For the future study, the LED phototherapy device will be applied for clinical research in collaboration with dermatologists.
1 December 2024 in IAES International Journal of Artificial Intelligence (IJ-AI)
It has been challenging to construct an autonomously controlled plant factory with artificial light (PFAL). It is also useful in engineering and bioscience research and education. The purpose of this research is to design and construct a micro-scale PFAL (µPFAL) with automatic environment control for a university project. Then, analyze the effectiveness of managing temperature, humidity, pH, EC, and CO2 on crop production, as well as the cost, and benefit of µPFAL. The µPFAL is made up of LED lighting, air condition, vertical cultivation, EC-pH regulation, a CO2 supply unit, and environmental control and monitoring. Control was provided via Arduino with PC monitor. For economic evaluation, cost-benefit analysis was used. The results of the control environment in µPFAL were achieved with a deviation of less than 2.5%. An Arduino-based environmental control system with a computer for monitoring was suited for university’s PFAL.Our µPFAL could produce 80.45 g/head fresh weight of green oak lettuce, the lettuce’s yield of 19 kg/m2/y. The payback period of µPFAL is 3.28 years, net present value of 82,543.30 THB, an internal rate of return of 24% and the B/C ratio of 1.22. Future research should include solar energy to assist µPFAL in meeting its sustainable goal.
1 December 2022 in Indonesian Journal of Electrical Engineering and Computer Science
Solar simulator is used to analysis characteristic of the solar cells. The non-uniformity is its major performance. The traditional non-uniformity measurement calls single detector method. The paper’s objective is to design and construct an array detector scanning system and to determine the optimal scanning time to achieve the lowest uncertainty. To investigate the non-uniformity by our proposed method and the traditional method, our detector consisted of eight photodiodes mounted on an arm of a linear motion lead screw to guide the detector scaning onto the lighting area. A microcontroller applied for controling and measuring light irradiance in 64 points corresponding to IEC 60904-9 standard. The results showed that the array detector scanned at a speed of 33.33 mm/s to obtain the non-uniformity with the lowest uncertainty, less than 0.6%. Analysis results of the non-uniformity obtained from our system on the test areas of (mm×mm) 156×156, 166×166 and 200×200 compared with the single detector. It showed that the mean absolute error was 1.27. Our system provided a lower uncertainty than the traditional method. The measurement accuracy was acceptable. The advantage is for testing on different test areas within a single device. The measurement time is around 1/32 of the traditional method.
1 December 2025 in Bulletin of Electrical Engineering and Informatics
The development of light-emitting diode (LED)-based solar simulators that comply with the updated IEC 60904-9:2020 standard, particularly achieving a Class A+ irradiance spectrum, remains a significant challenge. This necessitates careful consideration of two key spectral quality indicators: spectral deviation (SPD) and spectral coverage (SPC). This study proposes a method to achieve a Class A+ solar simulator spectrum using a minimal number of LED types while optimizing SPD and SPC. It also examines the influence of SPD and SPC on the photogenerated current density (Jph) and short-circuit current density (Jsc) of crystalline silicon and multi-crystalline silicon solar cells. By selectively adding ultraviolet (UV) and near-infrared (NIR) LEDs to the original six-type LED configuration, the simulator’s spectral performance was enhanced to more closely align with the AM1.5G standard. The configuration incorporating both UV and NIR LEDs demonstrated the highest performance. It achieved an SPC of 97.521% and the lowest SPD at 26.088%. Simulation results confirmed that higher SPC and lower SPD values contribute to reduced errors in the calculated Jsc and Jph for both crystalline silicon (c-Si) and multi-crystalline silicon (mc-Si) solar cells. These findings highlight the importance of well-balanced spectral design and demonstrate that accurate spectral simulation is achievable using only essential LED wavelengths.