Mirko Kariž

Dr. Mirko Kariž

Department of Wood Science and Technology, Biotechnical Faculty, Jamnikarjeva ulica 101, University of Ljubljana, 1000 Ljubljana, Slovenia
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2018 in Materials Today Communications
Verified
Journal Article
Closed access
Mirko KarižMirko Kariž
Mirko Kariž
MSMilan Sernek
Milan Sernek
MOMurčo Obućina
Murčo Obućina
MKManja Kitek Kuzman
Manja Kitek Kuzman

23 January 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
Nadir AyrilmisNadir Ayrilmis
Nadir Ayrilmis
Mirko KarižMirko Kariž
Mirko Kariž
JKJin Heon Kwon
Jin Heon Kwon
MKmanja Kuzman
manja Kuzman

15 March 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
Mirko KarižMirko Kariž
Mirko Kariž
Polymers filled with natural-based fillers have shown growing demand/interest in recent years, including in additive manufacturing. Like most natural fillers in 3D printing, wood particles serve mainly as a filler that lowers the cost of the printing material due to their low price. However, could wood be used as a main ingredient to affect/improve the properties of 3D-printed parts? Several advantages, such as its reinforcing ability, biodegradability, availability as waste material from other industries, ability to be used in different forms or only in partial components, recycling options or even the use of its undesirable hydromorph-induced dimensional instability for 4D printing, indicate the importance of exploring its use in 3D printing. A review of publications on 3D printing with wood biomass and technologies involving the use of wood particles and components was conducted to identify the possibilities of using wood in additive technologies and their potential.

4 November 2015 in European Journal of Wood and Wood Products
Verified
Journal Article
Closed access
PDF file
Mirko KarižMirko Kariž
Mirko Kariž
MSMilan Sernek
Milan Sernek
MKManja Kitek Kuzman
Manja Kitek Kuzman

12 May 2016 in European Journal of Wood and Wood Products
Verified
Journal Article
Closed access
PDF file
Mirko KarižMirko Kariž
Mirko Kariž
MKManja Kitek Kuzman
Manja Kitek Kuzman
MSMilan Sernek
Milan Sernek
MHMark Hughes
Mark Hughes
LRLauri Rautkari
Lauri Rautkari
AKAndreja Kutnar
Andreja Kutnar

14 August 2019 in International Journal of Polymer Analysis and Characterization
Verified
Journal Article
Closed access
Nadir AyrilmisNadir Ayrilmis
Nadir Ayrilmis
Mirko KarižMirko Kariž
Mirko Kariž
MKmanja Kuzman
manja Kuzman
Amount of wood flour was gradually increased from 0 to 50 wt% in the production of polylactic acid (PLA) based filaments with 1.75 mm diameter using twin screw extruder. Surface roughness and wettability were measured of the specimens. Surface roughness of the specimens significantly increased with incorporation of wood flour into PLA filament. Wettability of the specimens significantly decreased with increasing wood flour content. This was mainly attributed to the higher surface free energy of PLA than the beech wood. Contact angle values of the 3D printed wood/PLA specimens having wood flour content up to 30 wt% were less than 90°.