Daša Krapež Tomec

Mrs. Daša Krapež Tomec

Department of Wood Science and Tehnology, Biotechnical faculty, University of Ljubljana
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 March 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
Mirko KarižMirko Kariž
Mirko Kariž
Polymers filled with natural-based fillers have shown growing demand/interest in recent years, including in additive manufacturing. Like most natural fillers in 3D printing, wood particles serve mainly as a filler that lowers the cost of the printing material due to their low price. However, could wood be used as a main ingredient to affect/improve the properties of 3D-printed parts? Several advantages, such as its reinforcing ability, biodegradability, availability as waste material from other industries, ability to be used in different forms or only in partial components, recycling options or even the use of its undesirable hydromorph-induced dimensional instability for 4D printing, indicate the importance of exploring its use in 3D printing. A review of publications on 3D printing with wood biomass and technologies involving the use of wood particles and components was conducted to identify the possibilities of using wood in additive technologies and their potential.

9 April 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Mirko KarižMirko Kariž
Mirko Kariž
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
Sebastian DahleSebastian Dahle
Sebastian Dahle
MKmanja Kuzman
manja Kuzman
MSMilan Sernek
Milan Sernek
JŽJure Žigon
Jure Žigon
Additive manufacturing is becoming increasingly important for manufacturing end products, not just prototyping. However, the size of 3D-printed products is limited due to available printer sizes and other technological limitations. For example, making furniture from 3D-printed parts and wooden elements requires adequate adhesive joints. Since materials for 3D printing usually do not bond very well with adhesives designed for woodworking, they require special surface preparation to improve adhesion. In this study, fused deposition modelling (FDM) 3D-printed parts made of polylactic acid (PLA), polylactic acid with wood flour additive (Wood-PLA), and acrylonitrile-butadiene-styrene (ABS) polymers were bonded to wood with polyvinyl acetate (PVAc) adhesive. The surfaces of the samples were bonded as either non-treated, sanded, plasma treated, or sanded and plasma treated to evaluate the effect of each surface preparation on the bondability of the 3D-printed surfaces. Different surface preparations affected the bond shear strength in different ways. The plasma treatment significantly reduced water contact angles on all tested printing materials and increased the bond tensile shear strength of the adhesive used. The increase in bond strength was highest for the surfaces that had been both sanded and plasma treated. The highest increase was found for the ABS material (untreated 0.05 MPa; sanded and plasma treated 4.83 MPa) followed by Wood-PLA (from 0.45 MPa to 3.96 MPa) and PLA (from 0.55 MPa to 3.72 MPa). Analysis with a scanning electron microscope showed the smooth surfaces of the 3D-printed parts, which became rougher with sanding with more protruded particles, but plasma treatment partially melted the surface structures on the thermoplastic polymer surfaces.

9 December 2023 in European Journal of Wood and Wood Products
Verified
Journal Article
Open access
PDF file
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
MSMatthew Schwarzkopf
Matthew Schwarzkopf
RRRožle Repič
Rožle Repič
JŽJure Žigon
Jure Žigon
BGBojan Gospodarič
Bojan Gospodarič
Mirko KarižMirko Kariž
Mirko Kariž
This paper describes the development and characterisation of wood-filled polylactic acid (PLA) composite filaments for application in fused filament fabrication three-dimensional (3D) printing. Four different wood-polymer composite filaments for 3D printing were prepared, and specimens were 3D-printed with the obtained materials. The composite filaments consisted of wood particles (10% or 20% mass ratio) and a PLA polymer matrix. Wood particles were prepared by grinding and sieving non-modified beech wood and thermally modified (TM) (at 200 °C) beech wood. Thermal modification of wood affected particle preparation and smaller particles with lower aspect ratios were obtained. Filaments with TM wood particles were extruded better than with non-modified wood particles, with lower surface roughness and lower porosity. With a higher wood ratio, the surface roughness and porosity of the filament increased. Non-homogenous filaments also affected extrusion in 3D printing and reduced the properties of 3D-printed parts. Parts 3D-printed from filaments with TM particles had better tensile strength than from filaments with non-modified particles, but were lower than from pure PLA filaments. The tensile strength of the injection-moulded specimens was 18–69% higher than that of the 3D-printed specimens, depending on the filament composition. The results indicate some positive effects of thermal modification of wood particles on the properties of filaments and 3D-printed parts. Nevertheless, further optimisation of particle preparation and extrusion parameters is needed to obtain quality filaments with this size of wood particles.

22 September 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
Aleš StražeAleš Straže
Aleš Straže
AHAndreas Haider
Andreas Haider
Mirko KarižMirko Kariž
Mirko Kariž
The use of wood particles in wood-plastic composites (WPC) is well known and similar use could occur in materials for fused deposition modeling (FDM) 3D printing. Wood particles could be one of the possible solutions in the search for natural-based materials to minimize the use of synthetic-origin materials in additive manufacturing. Wood particles for 3D printing filaments can be made from wood waste and could serve as a cheap filler or as a value-added reinforcing component, depending on their properties and incorporation. The disadvantages of wood (dimensional changes due to water adsorption and desorption) could be used as functions when dimensional change is desirable, such as in shape-changing 4D printing materials. In this research, FDM printing materials made of polylactic acid (PLA), with different amounts of wood particles, were used to design moisture-induced shape-changing bilayer actuators, which could serve as a principle for active façade or ventilation valves. The initial research shows that the wood content in the WPC causes dimensional changes and thus shape changes of the designed actuators under changing climates. The shape change depends on the ratio of the materials in the two-layered actuator and the wood content in the wood-PLA composite used, and thus on sorption. The rate of the shape change behaves in the same way: the higher the wood content, the greater the change observed. The dynamics of the hygromorphism of bimaterial composites is greater with a small amount of added hygromechanically active material.

18 March 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
MSManfred Schöflinger
Manfred Schöflinger
JLJürgen Leßlhumer
Jürgen Leßlhumer
Urška Gradišar CentaUrška Gradišar Centa
Urška Gradišar Centa
JŽJure Žigon
Jure Žigon
Mirko KarižMirko Kariž
Mirko Kariž
This paper describes the use of microcrystalline cellulose (MCC) as an additive in wood-polylactic acid (PLA) filaments suitable for 3D printing. Filaments prepared with PLA, thermally modified (TM) wood, and three different MCC loadings (1, 3, and 5 wt%) by two-step melt blending in the extruder were characterized with respect to their rheological, thermal, and mechanical response. The analyses demonstrate that a low MCC content (1%) improves the mobility of the polymer chains and contributes to a higher elasticity of the matrix chain, a higher crystallinity, a lower glass transition temperature (by 1.66 °C), and a lower melting temperature (by 1.31 °C) and leads to a higher tensile strength (1.2%) and a higher modulus of elasticity (12.1%). Higher MCC loading hinders the mobility of the polymer matrix and leads to a rearrangement of the crystal lattice structure, resulting in a decrease in crystallinity. Scanning electron micrographs show that the cellulose is well distributed and dispersed in the PLA matrix, with some agglomeration occurring at higher MCC levels. The main objective of this study was to develop and evaluate a filament containing an optimal amount of MCC to improve compatibility between wood and PLA, optimize melt processability, and improve mechanical properties. It can be concluded that a 1% addition of MCC favorably changes the properties of the wood–PLA filaments, while a higher MCC content does not have this effect.

23 December 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SMSergej Medved
Sergej Medved
Daša Krapež TomecDaša Krapež Tomec
Daša Krapež Tomec
Angela BalzanoAngela Balzano
Angela Balzano
Maks MerelaMaks Merela
Maks Merela
Since invasive alien species are one of the main causes of biodiversity loss in the region and thus of changes in ecosystem services, it is important to find the best possible solution for their removal from nature and the best practice for their usability. The aim of the study was to investigate their properties as components of wood-plastic composites and to investigate the properties of the wood-plastic composites produced. The overall objective was to test the potential of available alien plant species as raw material for the manufacture of products. This would contribute to sustainability and give them a better chance of ending their life cycle. One of the possible solutions on a large scale is to use alien wood species for the production of wood plastic composites (WPC). Five invasive alien hardwood species have been used in combination with polyethylene powder (PE) and maleic anhydride grafted polyethylene (MAPE) to produce various flat pressed WPC boards. Microstructural analyses (confocal laser scanning microscopy and scanning electron microscopy) and mechanical tests (flexural strength, tensile strength) were performed. Furthermore, measurements of density, thickness swelling, water absorption and dimensional stability during heating and cooling were carried out. Comparisons were made between the properties of six WPC boards (five alien wood species and mixed boards). The results showed that the differences between different invasive alien wood species were less obvious in mechanical properties, while the differences in sorption properties and dimensional stability were more significant. The analyses of the WPC structure showed a good penetration of the polymer into the lumens of the wood cells and a fine internal structure without voids. These are crucial conditions to obtain a good, mechanically strong and water-resistant material.