Graphene-based materials are a family of carbonaceous structures that can be produced using a variety of processes either from graphite or other precursors. These materials are typically a few layered sheets of graphene in the form of platelets and maintain some of the properties of pristine graphene (such as two-dimensional platelet shape, aspect ratio, and graphitic bonding). In this work we present melt mixed graphene-based polypropylene systems with significantly reduced percolation threshold. Traditionally melt-mixed systems suffer from poor dispersion that leads to high electrical percolation values. In contrast in our work, graphene was added into an isotactic polypropylene matrix, achieving an electrical percolation threshold of ~1 wt.%. This indicates that the filler dispersion process has been highly efficient, something that leads to the suppression of the β phase that have a strong influence on the crystallization behavior and subsequent thermal and mechanical performance. The electrical percolation values obtained are comparable with reported solution mixed systems, despite the use of simple melt mixing protocols and the lack of any pre or post-treatment of the final compositions. The latter is of particular importance as the preparation method used in this work is industrially relevant and is readily scalable.

Plastic pollution has become a pressing environmental issue. The agricultural sector, in particular, is a significant contributor to this problem, given the widespread use of plastics in farming practices and a lack of and/or use of inefficient approaches for the recycling and valorization of agricultural plastic waste. This has resulted in the accumulation of these residues in landfills and/or their improper disposal, which has exacerbated their environmental impact, leading to negative consequences on soil, water, and ecosystems. This work provides an overview on the current methodologies available to address the challenges associated with inadequate management of agricultural plastics and highlights the need for a comprehensive and systematic methodology, involving material development, polymer processing, waste collection, sorting, and valorization. It emphasizes the importance of collaboration between polymer producers, polymer manufacturers, farmers, policymakers, waste management companies, and recyclers to develop effective, technical, and economically viable recycling and valorization schemes. This paper addresses gaps and provides guidance on possible solutions, specifically polymer development, policy instruments, regulatory frameworks, collection schemes, and the technical approaches required for the adequate valorization of agricultural plastic waste. Furthermore, it highlights the associated barriers and benefits of the different presented approaches. It also aims to promote awareness on agricultural plastic waste and provide guidance on the best approaches to reduce its environmental impact.

The mechanical properties of novel low percolation melt-mixed 3D hierarchical graphene/polypropylene nanocomposites are analyzed in this study. The analysis spans a broad range of techniques and time scales, from impact to tensile, dynamic mechanical behavior, and creep. The applicability of the time–temperature superposition principle and its limitations in the construction of the master curve for the isotactic polypropylene (iPP)-based graphene nanocomposites has been verified and presented. The Williams–Landel–Ferry method has been used to evaluate the dynamics and also Cole–Cole curves were presented to verify the thermorheological character of the nanocomposites. Short term (quasi-static) tensile tests, creep, and impact strength measurements were used to evaluate the load transfer efficiency. A significant increase of Young’s modulus with increasing filler content indicates reasonably good dispersion and adhesion between the iPP and the filler. The Young’s modulus results were compared with predicted modulus values using Halpin–Tsai model. An increase in brittleness resulting in lower impact strength values has also been recorded.

Crystallization of isotactic polypropylene (iPP) at the interface with crystalline films of two commercially employed nucleating agents (sodium benzoate (NaBz) and sodium 2,2’-methylene bis-(4,6-di-tert-butylphenyl)phosphate (NA-11)) and with a glass fiber (GF) was investigated using a polarized optical microscope. The analysis of the light intensity evolution during the crystallization process enabled the successful estimation of the time at which the crystal growth began, i.e., the induction time (t_i), at various crystallization temperatures. Meaningful differences in the t_i values were observed between the investigated systems. Moreover, the t_i data have been analyzed according to different nucleation models proposed in the literature, which consider either the time to form the first crystalline layer in contact with the substrate or the time required to grow a cluster of critical size. It has been found that the two models are applicable in different temperature ranges depending on the efficiency of the given substrate. Therefore, in order to obtain the value of the surface free energy difference function, Δσ, which is directly related to the nucleation energy barrier and useful for the definition of a universal nucleating efficiency scale, a model that considers both the above-mentioned times was fitted to the overall data. The values of Δσ for the nucleation of iPP on the surface of the different substrates are thus obtained and discussed in the framework of the literature results.