Aspen Plus has become one of the most common process simulation tools for both academia and industrial applications. In the last decade, the number of the papers on Aspen Plus modeling of biomass gasification has significantly increased. This review focuses on recent developments and studies on modeling biomass gasification in Aspen Plus including key aspects such as tar formation and model validation. Accordingly, challenges in modeling due to specific assumptions and limitations will be highlighted to provide a useful basis for researchers and end‐users for further process modeling of biomass gasification in Aspen Plus.
In this study, a low-temperature drying plant based on renewable energies to dry food processing wastes is investigated. The demand-oriented heat supply is realized by a solar wall in combination with a biomass boiler. Due to the operational complexity of such a system with different sub-units and process parameters, steady-state simulations were performed in Aspen Plus to provide an insight into the process. Moreover, a time-resolved energetic evaluation was conducted to analyze the influence of varying capacity of the heat sources and operational strategy in addition to economic calculations. The simulations showed that an overall control strategy needs to consider the air properties as well as the flow rate of wet input material. In the reference case, the boiler must be operated at full load through the year to supply as much heat as possible. The revenue from the dried material was the most crucial parameter on the drying economics. Although the current plant configuration operating at 12 h per day and five days per week enable feasible results, the drying process can be more profitable by doubling the boiler capacity and increasing operational hours to 24 h per day and five days per week. The proposed plant can provide an environmentally friendly and cost-effective solution for the re-valorization of food-processing wastes into added-value compounds.
Solid biofuels produced from torrefaction have improved coal-like properties in comparison to raw biofuels, yet ensuring uniform product quality is still a challenge. In this study, downstream torrefaction of wood pellets was performed at temperatures between 200 and 270 °C in a rotary kiln reactor to understand the effect of torrefaction temperature on product quality. The torrefied solid biofuel was compared with dedicated fuel properties defined in ISO/TS 17225-8:2016-12. Based on the results, the optimal temperature for downstream torrefaction was found at temperatures of 230 and 250 °C. Above this temperature, the effect of bulk density superimposes not only the increased net calorific value but also values for mechanical durability, amount of fines, and bulk density of the solid biofuel, which were below the thresholds of the fuel standard. Moreover, increasing process temperatures caused higher heavy metal concentrations in torrefied pellets. The composition of condensable and non-condensable fractions of the torr-gas substantially increased between temperatures of 230 and 250 °C and remained on a similar level at higher temperatures. Thus, the utilization of torr-gas for energy recovery purposes and as a precursor for the recovery of valuable chemicals should be balanced with the quality of the solid biofuel in the aforementioned range of torrefaction temperatures to enable the utilization of torrefaction products at further steps.
In this study, a small-scale (4.7 kWfuel) biomass burner based on “top-lit updraft” (TLUD) technology with automatic process control was developed for process heat generation. The combustion experiments were performed using wood pellets to gain more insights on the process, its repeatability and the behaviors of the emitted gaseous and particulate emissions under different combustion phases. The emission values were compared with similar small-scale combustion technologies as well as the emission limits defined in official regulations. The results showed that the average emissions (based on standardized 13 vol. % O2 content in the dry flue gas (STP)) over the entire process from start-up to switch-off were 29.4 mg/m3 for CO, 80 mg/m3 for NOx, and 3.6 mg/m3 for total particle matter (TPM) measured within the hot gas. These results were below the official limits for wood-fueled small-scale systems. The developed process control approach resulted in very low residual O2 content in the flue gas (approx. 2 vol. %), high flue gas temperatures and repetition accuracy. Thus, the process offers potential for further development in terms of process control, scale-up, and application in different areas.
In a world where billions of people still rely on unsustainable fuels and inefficient stoves, the need for clean cooking technologies has never been more urgent. However, the complexity of varying regional dynamics hinders one-size-fits-all solutions. Biomass cookstoves have been used for many years with a number of different models, prototypes, or products which are either already available in the market or still being researched. They can be one of the answers in paving the way to clean cooking, especially in developing regions. Yet, the selection of appropriate fuels and operating conditions is a crucial aspect that is often overlooked. Effective decision-making, based on case-specific evaluations, remains essential for the adoption of suitable technologies. This review paper provides a perspective on biomass cookstove technologies, addressing design and operational characteristics, the impact of pretreatment methods, and the potential applications of by-products. On this basis, a decision-making framework is proposed to facilitate the context-specific selection of biomass cookstoves. By integrating multiple factors, and real-world examples, the proposed approach aims to guide more informed decision-making for cookstove selection and contribute to accelerating progress toward universal clean cooking access. Our aim is to provide a practical and integrative perspective rather than a comprehensive systematic review, aiming to bridge the gap between theory and application for biomass-based clean cooking.
Based on the decision of representatives from the West African region and feedback from locals in Togo, an advanced continuous-feed, forced-draft, biomass cookstove named “Apeli” was developed. The stove was tested in modified ISO measurements based on the ISO 19867-1:2018 standard. This included a long shutdown operation using wood pellets and short shutdown operations using wood pellets, bamboo pellets, wheat straw pellets and palm kernel shells. Due to the fast shutdown capability, the short shutdown was chosen for more realistic results using this stove type. For cold start and long shutdown operation using wood pellets, the thermal efficiency is determined as 44.1% at a 1116 W power output by emitting 0.272 g CO and 17.2 mg PM 2.5 per MJd at high load. At low load, the efficiency is 38.0% at a 526 W power output by emitting 1.1 g CO and 45.1 mg PM 2.5 per MJd. Due to a misinterpretation of the standard, the burnout duration of the tests with long shutdown is approx. 1.5 min shorter than required. Using a worst-case approximation, values for a theoretical ISO-conforming measurement were calculated and rated according to the ISO 19867-3:2018 standard. The results showed that the Apeli would correspond to Tier 4 for efficiency and PM 2.5 as well as Tier 5 for CO in high-power operation using wood pellets. The use of alternative fuels is possible, but can lead to higher emissions compared to the use of wood pellets. With regard to possibly using the biochar produced in the process for soil application, it has been demonstrated that the PAH content ensures European BioChar-Agro-Organic limitations. The first results of a field test in Togo have shown that operating and feeding the stove by the target group is easy. The required permanent presence of the user during cooking with this stove seems to have a limited influence on acceptance, which seems to primarily depend on the age of the user. Moreover, it can be concluded that the Apeli has good potential to be mass-produced locally at low costs with a reliable supply of spare parts. This can contribute not only to improving clean cooking, but also to fighting air pollution and deforestation caused by solid fuel burning due to the reduced consumption of resources in the form of fuel, especially wood.