Converting omnipresent environmental energy through the assistance of spontaneous water evaporation is an emerging technology for sustainable energy systems. Developing bio‐based hydrovoltaic materials further pushes the sustainability, where wood is a prospect due to its native hydrophilic and anisotropic structure. However, current wood‐based water evaporation‐assisted power generators are facing the challenge of low power density. Here, an efficient hydrovoltaic wood power generator is reported based on wood cell wall nanoengineering. A highly porous wood with cellulosic network filling the lumen is fabricated through a green, one‐step treatment using sodium hydroxide to maximize the wood surface area, introduce chemical functionality, and enhance the cell wall permeability of water. An open‐circuit potential of ≈140 mV in deionized water is realized, over ten times higher than native wood. Further tuning the pH difference between wood and water, due to an ion concentration gradient, a potential up to 1 V and a remarkable power output of 1.35 µW cm−2 is achieved. The findings in this study provide a new strategy for efficient wood power generators.
Lignin is a promising candidate for energy storage because of its abundance, wide geographic distribution, and low cost as it is mainly available as a low value product from processing of wood into paper pulp. Lignin contains large amounts of potential quinone groups, which can be oxidized and reduced in a two electron process. This redox reaction makes lignin suitable for charge storage. However, lignin is insulating and therefore conductive materials are necessary in lignin electrodes, for whom the cost of the conductive materials hinders the scalable application. Among the organic conductive materials, graphite is one of the cheapest and is easily acquired from nature. In this work, we combine graphite and lignosulfonate (LS) and fabricate LS/graphite organic electrodes under a solvent-free mechanical milling method, without additives. The graphite is sheared into small particles with a size range from 50 nm to 2000 nm. Few-layer graphene is formed during the ball milling process. The LS/graphite hybrid material electrodes with primary stoichiometry of 4/1 (w/w) gives a conductivity of 280 S m−1 and discharge capacity of 35 mA h g−1. It is a promising material for the scalable production of LS organic electrodes.
Humic acid (HA) is a biopolymer formed from degraded plants, making it a ubiquitous, renewable, sustainable, and low cost source of biocarbon materials. HA contains abundant functional groups, such as carboxyl-, phenolic/alcoholic hydroxyl-, ketone-, and quinone/hydroquinone (Q/QH2)-groups. The presence of Q/QH2 groups makes HA redox active and, accordingly, HA is a candidate material for energy storage. However, as HA is an electronic insulator, it is essential to combine it with conductive materials in order to enable fabrication of HA electrodes. One of the lowest cost types of conductive materials that can be considered is carbon-based conductors such as graphite. Herein, we develop a facile method allowing the biocarbon to meet carbon; HA (in the form of a sodium salt) is mixed with graphite by a solvent-free mechanochemical method involving ball milling. Few-layer graphene sheets are formed and the HA/graphite mixtures can be used to fabricate HA/graphite hybrid material electrodes. These electrodes exhibit a conductivity of up to 160 S·m−1 and a discharge capacity as large as 20 mAhg−1. Our study demonstrates a novel methodology enabling scalable fabrication of low cost and sustainable organic electrodes for application as supercapacitors.
13 November 2021 in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
The sulphide stress cracking of high strength low alloy (HSLA) carbon steel C110 is related to the hydrogen absorption process. The objective of this research is to evaluate the effect of adsorbed H2S and Cl− on hydrogen permeation in C110, by studying the responses of hydrogen permeation current and characteristic inductance under environment with different H2S activities and NaCl concentrations using electrochemical methods, including hydrogen permeation method and electrochemical impedance spectroscopy (EIS). The hydrogen permeation current measured in Devanathan–Stachurski cell suggests that the enhance effect of the adsorbed H2S on the hydrogen absorption follows an adsorption isotherm behaviour as a function of H2S activity in solution. The inductive response of EIS under different H2S activities shows consistency with hydrogen permeation results. The EIS results also indicate that the coverage of H2S was suppressed by Cl−. A good correlation about the effect of adsorbed Cl− is found between inductive response and hydrogen permeation current.