Due to the high rise in luminous efficiency that high-brightness light-emitting diodes (HB-LEDs) have experienced in recent years, many new applications have been researched. This paper covers a streetlight LED application using the offline integrated buck-flyback converter (IBFC) developed in previous works. In this application, the converter is used to provide power-factor correction from a universal ac source. A control loop using the LM3524 IC has been implemented for testing the feasibility of Enabling pulsewidth modulation dimming mode. First, the LED load has been linearized and modeled in order to calculate the IBFC topology properly. Second, the converter has been designed and tested at the laboratory. The converter has also been modeled in order to design a fixed-frequency constant-current control. The dynamics of all the stages involved in the closed loop have been taken into account in order to develop an adequate controller. Finally, the experimental results obtained from the laboratory tests are discussed.

This paper deals with the capability of pulse width modulation (PWM) dimming operation added to the high-power factor-integrated buck-flyback converter (IBFC), which was developed in previous works for LED lighting applications. First, the two main dimming techniques will be introduced, namely, analog dimming and PWM dimming. Then, the three main PWM dimming schemes found in the literature, that is, enable dimming, series dimming, and parallel dimming, will be briefly discussed. Afterwards, the IBFC topology will be tested performing both analog and enable dimming. In addition, a new proposal is introduced: the high-frequency series PWM dimming technique, which overcomes all the challenges faced when developing PWM dimming capabilities in low slew-rate constant-current fixed-frequency-controlled converters and offers all the advantages of PWM dimming over analog dimming while maintaining good efficiency. The proposed dimming-technique control loop, as well as the laboratory tests, will be presented, discussed, and compared to analog dimming and PWM dimming, showing satisfactory results in terms of dimming ratio, input current total harmonic distortion (THD_I), and power factor.

Usually, pulsewidth modulation (PWM) operation is selected as the best dimming strategy to drive high-brightness LEDs. Nevertheless, to obtain an enhanced full linear dimming control of the device, the luminous flux should be measured. This paper proposes a control method based on an estimator of the luminous flux emitted by the LED. Based on the characterization of the LEDs, this estimator is defined. The estimator provides the flux value from only two temperature values (the case temperature and the ambient temperature). Once the estimator is validated, the electronic driver to supply the LEDs, as well as the digital control scheme, are presented. Such a control scheme is suitable for both AM and PWM dimming strategies. A prototype of the electronic driver has been built and tested, and experimental measurements of AM and PWM dimming are presented. It can be concluded that with the proposed estimator, the flux emitted by the LEDs can be accurately estimated. Thus, the output light control of the LEDs can be accomplished by sensing temperature rather than luminous flux. The final output characteristic of the system shows linearity between the output flux and the reference value, with AM as well as with PWM dimming of the LEDs.

In this paper, a new control method for electronic ballasts based on the use of a variable inductor is presented. The main goal is to perform the complete control of the electronic ballast by maintaining the switching frequency constant and without using other parameters of the power converter, such as input voltage or duty cycle. The magnetic regulator is controlled by means of a dc current, which allows performing both lamp soft starting and lamp dimming. Apart from the important advantage of keeping a constant frequency during full electronic ballast operation, the proposed method presents additional advantages when compared to other control methods, such as inherent isolated control, more linear control characteristics, constant electrode power, and higher efficiency. Experimental results from a 36-W linear fluorescent lamp prototype are presented.

Due to the high rise in luminous efficiency that HB-LEDs have experienced in the last recent years, many new applications have been researched. In this paper, a streetlight LED application will be covered, using the integrated buck-flyback converter developed in previous works, which performs power factor correction (PFC) from a universal AC source, as well as a control loop using the LM3524 IC, which allows PWM dimming operation mode. Firstly, the LED load will be linearized and modeled in order to calculate the IBFC topology properly. Afterwards, the converter will be calculated, presenting the one built in the lab. Secondly, the converter will be modeled in order to build the closed loop system, modeling the current sensor as well in order to develop an adequate controller. Finally, experimental results obtained from the lab tests will be presented.