Due to the high rise in luminous efficiency that high-brightness light-emitting diodes (HB-LEDs) have experienced in recent years, many new applications have been researched. This paper covers a streetlight LED application using the offline integrated buck-flyback converter (IBFC) developed in previous works. In this application, the converter is used to provide power-factor correction from a universal ac source. A control loop using the LM3524 IC has been implemented for testing the feasibility of Enabling pulsewidth modulation dimming mode. First, the LED load has been linearized and modeled in order to calculate the IBFC topology properly. Second, the converter has been designed and tested at the laboratory. The converter has also been modeled in order to design a fixed-frequency constant-current control. The dynamics of all the stages involved in the closed loop have been taken into account in order to develop an adequate controller. Finally, the experimental results obtained from the laboratory tests are discussed.
22 March 2011 in IEEE Transactions on Industrial Electronics
This paper deals with the capability of pulse width modulation (PWM) dimming operation added to the high-power factor-integrated buck-flyback converter (IBFC), which was developed in previous works for LED lighting applications. First, the two main dimming techniques will be introduced, namely, analog dimming and PWM dimming. Then, the three main PWM dimming schemes found in the literature, that is, enable dimming, series dimming, and parallel dimming, will be briefly discussed. Afterwards, the IBFC topology will be tested performing both analog and enable dimming. In addition, a new proposal is introduced: the high-frequency series PWM dimming technique, which overcomes all the challenges faced when developing PWM dimming capabilities in low slew-rate constant-current fixed-frequency-controlled converters and offers all the advantages of PWM dimming over analog dimming while maintaining good efficiency. The proposed dimming-technique control loop, as well as the laboratory tests, will be presented, discussed, and compared to analog dimming and PWM dimming, showing satisfactory results in terms of dimming ratio, input current total harmonic distortion (THDI), and power factor.
Energy storage systems (ESSs) are gaining a lot of interest due to the trend of increasing the use of renewable energies. This paper reviews the different ESSs in power systems, especially microgrids showing their essential role in enhancing the performance of electrical systems. Therefore, The ESSs classified into various technologies as a function of the energy storage form and the main relevant technical parameters. In this review paper, the most common classifications are presented, summarized, and compared according to their characteristics. A specific interest in electrochemical ESSs, especially battery energy storage systems, focusing on their classifications due to their importance in the residential sector. Besides that, the benefits and drawbacks of Lithium-Ion (Li-Ion) batteries are discussed due to their significance. Finally, the environmental impact of these ESSs is discussed.
18 February 2009 in IEEE Transactions on Power Electronics
Usually, pulsewidth modulation (PWM) operation is selected as the best dimming strategy to drive high-brightness LEDs. Nevertheless, to obtain an enhanced full linear dimming control of the device, the luminous flux should be measured. This paper proposes a control method based on an estimator of the luminous flux emitted by the LED. Based on the characterization of the LEDs, this estimator is defined. The estimator provides the flux value from only two temperature values (the case temperature and the ambient temperature). Once the estimator is validated, the electronic driver to supply the LEDs, as well as the digital control scheme, are presented. Such a control scheme is suitable for both AM and PWM dimming strategies. A prototype of the electronic driver has been built and tested, and experimental measurements of AM and PWM dimming are presented. It can be concluded that with the proposed estimator, the flux emitted by the LEDs can be accurately estimated. Thus, the output light control of the LEDs can be accomplished by sensing temperature rather than luminous flux. The final output characteristic of the system shows linearity between the output flux and the reference value, with AM as well as with PWM dimming of the LEDs.
2 June 2014 in IEEE Transactions on Industrial Electronics
This paper presents a new control method and a detailed project methodology for the optimized connection method of two converters, aiming to reduce the redundant power processing, in order to supply high-power light-emitting diodes (LEDs) with reduced capacitance and high efficiency, directly from the ac line. This connection method allows dealing with two major issues related to the LED driver: capacitance reduction and efficiency increasing. The first converter provides power factor correction, whereas the second converter controls the current through the LED. The basic idea consists in making the second converter to process only the low-frequency ripple (LFR) of the first converter, thus smoothing the LED current. In this way, the LFR is managed by the second stage, so that the capacitance of the first stage can be significantly reduced. The proposed control method can achieve better results for the low-frequency compensation. In addition to that, a high power factor and a low harmonic content are obtained, fulfilling the IEC 61000-3-2 Class C requirements. A laboratory prototype with a rated power of 75 W and an input voltage of 220 V rms /60 Hz was built in order to show the feasibility of the idea. The measured overall efficiency of the converter was 91%, and electrolytic capacitors were avoided.
3 March 2008 in IEEE Transactions on Industrial Electronics
In this paper, a novel single-stage electronic ballast with a high power factor is presented. The ballast circuit is based on the integration of a buck converter to provide the power factor correction, and a flyback converter to control the lamp power and to supply the lamp with a low-frequency square-waveform current. Both converters work in discontinuous conduction mode, which simplifies the control. In spite of being an integrated topology, the circuit does not present additional stress of voltage or current in the main switch, which handles only the flyback or buck current, depending on the operation mode. To supply the lamp with a low-frequency square-wave current to avoid acoustic resonances, the flyback has two secondary windings that operate complementarily at a low frequency. The design procedure of the converters is also detailed. Experimental results from a 35-W metal halide lamp are presented, where the proposed ballast reached a power factor of 0.95, a total harmonic distortion of 30% (complying with IEC 61000-3-2), and an efficiency of 90%.